Elo zero-bezel PCAP touchscreen display (MS601692) screw size
M4 · 7 mm long
The screws used on Elo zero-bezel PCAP touchscreen display (MS601692) are M4, 7 mm long.
Where it is used: VESA 100x100 threads, max thread depth 7mm.
This entry is marked confirmed and comes from docs.elotouch.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Elo zero-bezel PCAP touchscreen display (MS601692) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 7 mm | 0.7 mm | not stated | not stated | VESA 100x100 threads, max thread depth 7mm | Confirmed |
Fitment records and sources
VESA 100x100 threads, max thread depth 7mm
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 7 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- VESA fixes the hole pattern and max thread depth, not screw length — length depends on the panel back and any spacers.
- VESA thread size is set by pattern class: M4 for 75x75/100x100, M6 or M8 for the big 200mm+ patterns. Check the plate on the back of the display.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Elo zero-bezel PCAP touchscreen display (MS601692), closest length match first.
- Portable 13-15in travel monitors also M4 × 7 mm
- LED aluminium channel end caps also M4 × 7 mm
- Bopla earthing screw for cable gland / general accessories also M4 × 7 mm
- LED video wall cabinet headless bolt E also M4 × 7 mm
- GCX 75/100mm VESA flush display mount also M4 × 7 mm
- VESA FDMI Part B and C display mounts also M4 × 7 mm
- HP LaserJet family common hardware also M4 × 7 mm
- Fishing reel side plates also M4 × 7 mm
Questions about Elo zero-bezel PCAP touchscreen display (MS601692) screws
- What size screw does Elo zero-bezel PCAP touchscreen display (MS601692) use?
- M4 × 7 mm for VESA 100x100 threads, max thread depth 7mm.
- How long are the screws in Elo zero-bezel PCAP touchscreen display (MS601692)?
- The record gives 7 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Elo zero-bezel PCAP touchscreen display (MS601692)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.