Entrelec/ABB M4/6 feed-through terminal block screw size
M4 · length not stated in the sources
If you are replacing a screw on Entrelec/ABB M4/6 feed-through terminal block, the thread is M4. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for 4mm2 DIN-rail terminal block with M4 screw-clamp connection.
This entry is marked confirmed and comes from cse-distributors.co.uk.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Entrelec/ABB M4/6 feed-through terminal block screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | 4mm2 DIN-rail terminal block with M4 screw-clamp connection | Confirmed |
Fitment records and sources
4mm2 DIN-rail terminal block with M4 screw-clamp connection
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- There is no single standard Picatinny/rail screw size; makers use metric M3/M4 and imperial 6-48 or 8-40 interchangeably. Always measure the existing screw.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Vehicles, Marine & Mobility
The same screw also fits
Devices whose records share a thread with Entrelec/ABB M4/6 feed-through terminal block, closest length match first.
- Segway-Ninebot Dashboard assembly screws (6 pcs) also M4
- Kasuga/Misumi BN & BNH DIN-rail terminal blocks also M4
- Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00) also M4
- Garmin zumo XT Motorcycle mount base plate to handlebar mount (panhead screws) also M4
- DIN rail terminal block, M4 screw-terminal version also M4
- Phoenix Contact CHARX EV-T1CCS charging inlet repair kit also M4
- Shimano derailleur limit screws (H/L limit and B-tension) also M4
- Ducati Monster 696 also M4
Questions about Entrelec/ABB M4/6 feed-through terminal block screws
- What size screw does Entrelec/ABB M4/6 feed-through terminal block use?
- M4 for 4mm2 DIN-rail terminal block with M4 screw-clamp connection.
- How long are the screws in Entrelec/ABB M4/6 feed-through terminal block?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Entrelec/ABB M4/6 feed-through terminal block?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.