Framework Laptop 13 fingerprint reader / touchpad screw screw size
M1.4 · 1.8 mm long
If you are replacing a screw on Framework Laptop 13 fingerprint reader / touchpad screw, the thread is M1.4, 1.8 mm long.
The record covers PH0 head, 4.0mm head dia.
Head and drive, as the source states them: Phillips PH0 drive.
This entry is marked confirmed and comes from guides.frame.work.
An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Framework Laptop 13 fingerprint reader / touchpad screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 1.8 mm | 0.3 mm | not stated | Phillips PH0 | PH0 head, 4.0mm head dia | Confirmed |
Fitment records and sources
PH0 head, 4.0mm head dia
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 1.8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Phillips PH0 drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Framework Laptop 13 fingerprint reader / touchpad screw, closest length match first.
- Framework Laptop 13 touchpad and fingerprint reader also M1.4 × 1.8 mm
- Framework Laptop 16 (AMD Ryzen AI 300) also M1.4 × 1.8 mm
- Framework Laptop 16 also M1.4 × 1.8 mm
- Framework Laptop 16 (PH0 1.8 mm) also M1.4 × 1.8 mm
- Fitbit / fitness band back cover also M1.4 × 1.8 mm
- Hearing aid shells also M1.4 × 1.8 mm
- Clock balance cock and pallet screws also M1.4 × 1.8 mm
- Apple Watch case screws also M1.4 × 1.8 mm
Questions about Framework Laptop 13 fingerprint reader / touchpad screw screws
- What size screw does Framework Laptop 13 fingerprint reader / touchpad screw use?
- M1.4 × 1.8 mm for PH0 head, 4.0mm head dia.
- How long are the screws in Framework Laptop 13 fingerprint reader / touchpad screw?
- The record gives 1.8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Framework Laptop 13 fingerprint reader / touchpad screw?
- The source lists a Phillips PH0 drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Framework Laptop 13 fingerprint reader / touchpad screw?
- TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.