Framework Laptop 16 (PH0 1.8 mm) screw size
M1.4 · 1.8 mm long
Framework Laptop 16 (PH0 1.8 mm) takes M1.4 metric screws, 1.8 mm long.
Where it is used: official fastener guide: PH0 head, 1.8 mm length, 4.0 mm head diameter.
Head and drive, as the source states them: Phillips PH0 drive.
This entry is marked confirmed and comes from ifixit.com.
M1.4 means a 1.4 mm nominal diameter with a 0.3 mm thread pitch. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Framework Laptop 16 (PH0 1.8 mm) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 1.8 mm | 0.3 mm | not stated | Phillips PH0 | Official fastener guide: PH0 head, 1.8 mm length, 4.0 mm head diameter | Confirmed |
Fitment records and sources
Official fastener guide: PH0 head, 1.8 mm length, 4.0 mm head diameter.
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 1.8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Phillips PH0 drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Framework Laptop 16 (PH0 1.8 mm), closest length match first.
- Framework Laptop 16 also M1.4 × 1.8 mm
- Framework Laptop 16 (AMD Ryzen AI 300) also M1.4 × 1.8 mm
- Framework Laptop 13 touchpad and fingerprint reader also M1.4 × 1.8 mm
- Framework Laptop 13 fingerprint reader / touchpad screw also M1.4 × 1.8 mm
- NBK SPE-MC PEEK micro pan head screws also M1.4 × 1.8 mm
- Hearing aid shells also M1.4 × 1.8 mm
- Apple Watch case screws also M1.4 × 1.8 mm
- Clock balance cock and pallet screws also M1.4 × 1.8 mm
Questions about Framework Laptop 16 (PH0 1.8 mm) screws
- What size screw does Framework Laptop 16 (PH0 1.8 mm) use?
- M1.4 × 1.8 mm for official fastener guide: PH0 head, 1.8 mm length, 4.0 mm head diameter.
- How long are the screws in Framework Laptop 16 (PH0 1.8 mm)?
- The record gives 1.8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Framework Laptop 16 (PH0 1.8 mm)?
- The source lists a Phillips PH0 drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Framework Laptop 16 (PH0 1.8 mm)?
- TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.