Fuge EVOLVE ski binding mounting jig screw size
M4 · 10 mm long
Fuge EVOLVE ski binding mounting jig takes M4 metric screws, 10 mm long.
The record covers eight screws for initial jig assembly, 2.5mm hex key.
Head and drive, as the source states them: Hex socket (Allen) drive.
This entry is marked confirmed and comes from fugeskis.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Fuge EVOLVE ski binding mounting jig screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10 mm | 0.7 mm | not stated | Hex socket (Allen) | Eight screws for initial jig assembly, 2.5mm hex key | Confirmed |
Fitment records and sources
Eight screws for initial jig assembly, 2.5mm hex key
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Outdoor hardware should be stainless or coated to stop corrosion seizing it in place.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Hex socket (Allen) drive. For comparison, standard M4 heads take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- US-made pinball machines (Williams/Bally/Stern) overwhelmingly use imperial UTS threads (#6-32, #8-32, #10-32); explicit metric threads only appear on newer/import components such as Jersey Jack Pinball's Hobbit Smaug assembly (M3).
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Sports, Outdoors & Optics Mounts
The same screw also fits
Devices whose records share a thread with Fuge EVOLVE ski binding mounting jig, closest length match first.
- Heart rate chest strap buckle also M4 × 10 mm
- Fishing reel side plates also M4 × 10 mm
- Ring video doorbell mounting hardware also M4 × 10 mm
- Wurth Elektronik WA-SSTIE steel spacer stud also M4 × 10 mm
- Dell U2417HJ also M4 × 10 mm
- 19-inch rack cage nut (light equipment) also M4 × 10 mm
- LG 43LJ5000 also M4 × 10 mm
- Dell P1917S also M4 × 10 mm
Questions about Fuge EVOLVE ski binding mounting jig screws
- What size screw does Fuge EVOLVE ski binding mounting jig use?
- M4 × 10 mm for eight screws for initial jig assembly, 2.5mm hex key.
- How long are the screws in Fuge EVOLVE ski binding mounting jig?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Fuge EVOLVE ski binding mounting jig?
- The source lists a Hex socket (Allen) drive. Standard M4 heads otherwise take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.