Burton EST bindings on The Channel screw size
M6 · 13 mm long
Our records put Burton EST bindings on The Channel on M6 screws, 13 mm long.
The record covers burton's M6 Channel EST hardware set mounts EST bindings to Channel boards using four M6x13 screws with tabbed washers.
This entry is marked confirmed and comes from tactics.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Burton EST bindings on The Channel screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 13 mm | 1 mm | not stated | not stated | Burton's M6 Channel EST hardware set mounts EST bindings to Channel boards using four M6x13 screws with tabbed washerswasher / flange face | Confirmed |
Fitment records and sources
Burton's M6 Channel EST hardware set mounts EST bindings to Channel boards using four M6x13 screws with tabbed washers.
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Outdoor hardware should be stainless or coated to stop corrosion seizing it in place.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 13 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Burton sells two different M6 lengths: M6x16 for Re:Flex on 4x4/3D boards and M6x13 for EST on Channel boards. The 16mm screw can bottom out or dimple a Channel board base.
- Trailer license plate mounts frequently use 1/4 inch screws in the US, but international and many modern bracket kits have shifted to M6.
More in Sports, Outdoors & Optics Mounts
Accuracy International AT/AX AICS chassisAlpine binding heel/toe piece (heavy duty)Archery/bow accessory set screws (generic component, not confirmed as sight-specific)Bodypoint wheelchair T-slot mounting kitBurton Re:Flex snowboard bindings (4x4 / 3D boards)Elliptical pedal arm boltsFishing reel handle and drag knobFishing reel handle screw/nut locking plateFishing reel side platesFuge EVOLVE ski binding mounting jigHeart rate chest strap buckleISMS scope mount (Ideal Scope Mounting System)
Browse all 30 in Sports, Outdoors & Optics Mounts →The same screw also fits
Devices whose records share a thread with Burton EST bindings on The Channel, closest length match first.
- Burton Re:Flex snowboard bindings (4x4 / 3D boards) also M6 × 13 mm
- Alpine binding heel/toe piece (heavy duty) also M6 × 13 mm
- IV pole clamps also M6 × 13 mm
- 3030 extrusion T-nuts (heavy duty) also M6 × 13 mm
- Wurth Elektronik WA-SSTIE steel spacer stud also M6 × 13 mm
- Motorcycle fairing panels also M6 × 13 mm
- Carbide3D Shapeoko 5 Pro CNC router also M6 × 13 mm
- Car license plate U-clip retaining fasteners (trim) also M6 × 13 mm
Questions about Burton EST bindings on The Channel screws
- What size screw does Burton EST bindings on The Channel use?
- M6 × 13 mm for burton's M6 Channel EST hardware set mounts EST bindings to Channel boards using four M6x13 screws with tabbed washers.
- How long are the screws in Burton EST bindings on The Channel?
- The record gives 13 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Burton EST bindings on The Channel?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.