What size screw does Kenwood TK-8302 transceiver use?

M3 × 8 mm for M3 x 8mm screw in the exploded-view parts list.

How long are the screws in Kenwood TK-8302 transceiver?

The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Kenwood TK-8302 transceiver?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Kenwood TK-8302 transceiver?

TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Kenwood TK-8302 transceiver screw size

M3 · 8 mm long

Kenwood TK-8302 transceiver takes M3 metric screws, 8 mm long.

The record covers M3 x 8mm screw in the exploded-view parts list.

This entry is marked confirmed and comes from manuals.repeater-builder.com.

An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Kenwood TK-8302 transceiver screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	8 mm	0.5 mm	not stated	not stated	M3 x 8mm screw in the exploded-view parts list	Confirmed

Fitment records and sources

M38mmconfirmed

M3 x 8mm screw in the exploded-view parts list

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

If several screws hold the same part, check that they are all the same length before assuming they are.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

Power-tool gearcase and clamshell screws are usually thread-forming (marked "ST") even when the parts list gives an M-size — a normal machine screw of the same size may not hold in the plastic boss.
Blender, toothbrush and shaver teardowns list Torx/Phillips bit sizes only; a T8 bit tells you nothing about the thread.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Other Equipment

2020 aluminium extrusion T-nuts Acer Aspire / Swift Allen-Bradley PowerFlex 520-series mounting adapter plate Allen-Bradley PowerFlex 750-series Allen-Bradley PowerFlex 750-series I/O shield termination Allen-Bradley PowerFlex 755 IP00 control pod Amiga 500 rear/front case screws (Retro32 replacement set)Arduino Uno / Mega ASUS / MSI / Gigabyte / ASRock motherboards Backscatter FLIP3.1 underwater filter frame screws (2x)Backscatter FLIP3.1 underwater flip-frame retaining screw Bosch Rexroth swivel-in T-slot nut, slot 8

Browse all 125 in Other Equipment →

The same screw also fits

Devices whose records share a thread with Kenwood TK-8302 transceiver, closest length match first.

2020 aluminium extrusion T-nuts also M3 × 8 mm
Eschmann LS5 / SES2555 autoclave also M3 × 8 mm
Arduino Uno / Mega also M3 × 8 mm
Kern PFB precision balance internal hardware also M3 × 8 mm
PSU internals & fan grilles also M3 × 8 mm
Amiga 500 rear/front case screws (Retro32 replacement set) also M3 × 8 mm
Backscatter FLIP3.1 underwater filter frame screws (2x) also M3 × 8 mm
Floyd Rose locking tremolo saddles also M3 × 8 mm

Questions about Kenwood TK-8302 transceiver screws

What size screw does Kenwood TK-8302 transceiver use?: M3 × 8 mm for M3 x 8mm screw in the exploded-view parts list.
How long are the screws in Kenwood TK-8302 transceiver?: The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Kenwood TK-8302 transceiver?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Kenwood TK-8302 transceiver?: TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Heads up: shipping delay