Kirisun T60/T65 handheld two-way radio chassis screws screw size
M2 · 4 to 6 mm long
If you are replacing a screw on Kirisun T60/T65 handheld two-way radio chassis screws, the thread is M2 in lengths from 4 to 6 mm.
The record covers service manual for handheld radio disassembly covers chassis/battery-door fastener removal; Kirisun's documented handheld radio service manuals for this class specify M2 metric case screws in their screw/torque tables.
This entry is marked likely and comes from kirisun.com.
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Kirisun T60/T65 handheld two-way radio chassis screws screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 4–6 mm | 0.4 mm | not stated | not stated | Service manual for handheld radio disassembly covers chassis/battery-door fastener removal; Kirisun's documented handheld radio service manuals for this class specify M2 metric case screws in their screw/torque tables | Likely |
Fitment records and sources
Service manual for handheld radio disassembly covers chassis/battery-door fastener removal; Kirisun's documented handheld radio service manuals for this class specify M2 metric case screws in their screw/torque tables
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Phone and wearable screws are tiny and often differ by fractions of a millimetre between positions; keep each one next to the hole it came from.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 4–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- Apple Watch band lugs use a proprietary spring-bar/pin interface, not a metric screw - do not shop for an M-size there.
- M.2 SSD mounting screws (M2 x 3mm) are frequently mislabeled generically as 'M.2 screws' which can be confused with the M2 metric thread designation — they do coincide numerically here but are conceptually distinct (M.2 = card format, M2 = thread size).
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for HP Omen Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for Audiophile Headphone Headband Repair - Pack of 50 Black
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Phones, Tablets & Wearables
Akuvox A08 video doorbellAkuvox A08 video doorbell (back plate)Anbernic RG35XX rear case screwsApple Watch case screwsApple Watch strap adapterASUS ROG Ally (RC71L)Asus ROG Ally (RC71L) back panel and M.2 2230 SSD coverASUS ROG Ally RC71L rear shellCompact smart sensor PCBsDive watch bezel insertDive watch bezelsExtech 407732 sound level meter battery cover screw
Browse all 134 in Phones, Tablets & Wearables →The same screw also fits
Devices whose records share a thread with Kirisun T60/T65 handheld two-way radio chassis screws, closest length match first.
- PS5 SSD expansion slot also M2 × 4 mm
- Mid-range Android tablet frames also M2 × 4–5 mm
- Kindle Paperwhite internal boards also M2 × 4 mm
- Samsung Galaxy A-series (SM-A013 to SM-A075) also M2 × 4 mm
- Kindle / Kobo e-reader back case also M2 × 4–5 mm
- Steam Deck internal shields also M2 × 4–6 mm
- PS4 internal HDD bay and shields also M2 × 4–6 mm
- PS5 M.2 SSD expansion slot cover plate also M2 × 5–6 mm
Questions about Kirisun T60/T65 handheld two-way radio chassis screws screws
- What size screw does Kirisun T60/T65 handheld two-way radio chassis screws use?
- M2 × 4–6 mm for service manual for handheld radio disassembly covers chassis/battery-door fastener removal; Kirisun's documented handheld radio service manuals for this class specify M2 metric case screws in their screw/torque tables.
- How long are the screws in Kirisun T60/T65 handheld two-way radio chassis screws?
- The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Kirisun T60/T65 handheld two-way radio chassis screws?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Kirisun T60/T65 handheld two-way radio chassis screws?
- TechSpareWarehouse (our own store) lists M2 x 4mm, M2 x 5mm and M2 x 6mm, which match lengths in the records above.