PS4 internal HDD bay and shields screw size
M2 · 4 to 6 mm long
PS4 internal HDD bay and shields takes M2 metric screws in lengths from 4 to 6 mm.
It is listed for phillips screws for internal brackets.
Head and drive, as the source states them: Phillips drive.
This entry is marked reported and comes from ifixit.com.
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
PS4 internal HDD bay and shields screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 4–6 mm | 0.4 mm | not stated | Phillips | Phillips screws for internal brackets | Reported |
Fitment records and sources
Phillips screws for internal brackets
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Over-long screws in phones are a known cause of damaged boards (Apple's 'long screw damage'), so never swap positions.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 4–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for HP Omen Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for Audiophile Headphone Headband Repair - Pack of 50 Black
$4.99
-
Dell Latitude 5530 Replacement Screws Sold Individually – M2 x 3mm, M2 x 4mm, M2.5 x 5mm Phillips Wafer Head, Black
$0.10Choose size -
HP EliteBook 840 G8 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 4mm, M2.5 x 4mm Phillips Wafer Head, Black
$0.10Choose size
More in Phones, Tablets & Wearables
Akuvox A08 video doorbellAkuvox A08 video doorbell (back plate)Anbernic RG35XX rear case screwsApple Watch case screwsApple Watch strap adapterASUS ROG Ally (RC71L)Asus ROG Ally (RC71L) back panel and M.2 2230 SSD coverASUS ROG Ally RC71L rear shellCompact smart sensor PCBsDive watch bezel insertDive watch bezelsExtech 407732 sound level meter battery cover screw
Browse all 134 in Phones, Tablets & Wearables →The same screw also fits
Devices whose records share a thread with PS4 internal HDD bay and shields, closest length match first.
- Steam Deck internal shields also M2 × 4–6 mm
- Kindle / Kobo e-reader back case also M2 × 4–5 mm
- Samsung Galaxy A-series (SM-A013 to SM-A075) also M2 × 4 mm
- Kindle Paperwhite internal boards also M2 × 4 mm
- Mid-range Android tablet frames also M2 × 4–5 mm
- Kirisun T60/T65 handheld two-way radio chassis screws also M2 × 4–6 mm
- PS5 SSD expansion slot also M2 × 4 mm
- PS5 internal M.2 SSD retention screw also M2 × 4–5 mm
Questions about PS4 internal HDD bay and shields screws
- What size screw does PS4 internal HDD bay and shields use?
- M2 × 4–6 mm for phillips screws for internal brackets.
- How long are the screws in PS4 internal HDD bay and shields?
- The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for PS4 internal HDD bay and shields?
- The source lists a Phillips drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for PS4 internal HDD bay and shields?
- TechSpareWarehouse (our own store) lists M2 x 4mm, M2 x 5mm and M2 x 6mm, which match lengths in the records above.