Large drones (Matrice-class payloads) screw size
M6 · 10 to 20 mm long
Large drones (Matrice-class payloads) takes M6 metric screws in lengths from 10 to 20 mm.
It is listed for payload and gimbal mounting plates.
This entry is marked reported.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Large drones (Matrice-class payloads) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 10–20 mm | 1 mm | not stated | not stated | payload and gimbal mounting plates | Reported |
Fitment records and sources
payload and gimbal mounting plates
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Frame and motor screws must not reach the motor windings; check the length against the motor's mounting depth.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Hygienic/3-A food-industry M6 screws are a distinct fastener class (with integrated sealing gasket/washer) from standard DIN 912 M6 socket-head screws; substituting a plain DIN 912 M6 screw on food/sanitary equipment breaks the hygienic seal even though the thread is nominally the same size.
- UR cobot flange bolts are commonly sold/quoted as 'M6 bolts' but the required length depends on the tool thickness; UR's own guidance is bolt class M6-8.8 to ISO4762 without a fixed length, so length must be selected per adapter/tool stack-up, not assumed as a fixed mm value.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M6 x 16mm Black Wafer Head Rack Screws for Rittal DK 7094.100 / 7094.110 / 7094.140 19-inch Rack – 20-Pack Replacement
$8.99Choose size -
M6 x 16mm Black Wafer Head Awning & Box Screws for Thule Awning 326 / 327 / 328, Conduit Box 317 & Xpedition 820 / 821 (50333) – 8-Pack Replacement
$6.99Choose size -
M6 x 12mm Black Wafer Head TV Back-Panel Screws for Vizio VQD65R-1004, VQD70R-1001, VQM55C-1004, VQM65C-1004 – 8-Pack Replacement
$6.99Choose size -
M6 x 12mm Black Wafer Head Brake Line Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 8-Pack Replacement
$6.99Choose size
More in Drones, RC & Gimbals
1/10 scale RC cars1/8 scale RC car chassis hardware3D-printed FPV stack mounts and spacers5-inch brushless motor to armAirsoft V2 / EHPA gearbox shellsALware Quad Flyer Spider 500 quadcopter kitAntique wall clock pendulum bracketsArcade marquee retainersARRMA Senton (and similar 1/10 vehicles)ARRMA Senton/kingpin-equipped vehiclesAxial Racing crawler/buggy kitsAxial SCX10 III RC crawler chassis
Browse all 144 in Drones, RC & Gimbals →The same screw also fits
Devices whose records share a thread with Large drones (Matrice-class payloads), closest length match first.
- BMW Motorcycles (Various Models) also M6 × 16 mm
- Dell U4320Q also M6 × 12 mm
- Gas grill control panel also M6 × 10–20 mm
- Roces inline skate frame mounting bolt also M6 × 14–20 mm
- Kestrel e400nb wind turbine also M6 × 16 mm
- Carbide 3D 80mm VFD spindle mount kit also M6 × 20 mm
- Hillrom/Baxter hospital bed hardware also M6 × 10 mm
- Rack ears on pro-audio gear also M6 × 10–12 mm
Questions about Large drones (Matrice-class payloads) screws
- What size screw does Large drones (Matrice-class payloads) use?
- M6 × 10–20 mm for payload and gimbal mounting plates.
- How long are the screws in Large drones (Matrice-class payloads)?
- The records range from 10 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Large drones (Matrice-class payloads)?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.