LX9000 glider glide-computer panel screw screw size
M2.5 · 10 mm long
If you are replacing a screw on LX9000 glider glide-computer panel screw, the thread is M2.5, 10 mm long.
It is listed for M2.5 x 10mm painted Nextel-finish instrument screw for glider instrument panels.
This entry is marked confirmed and comes from shop.streckenflug.at.
An M2.5 screw is 2.5 mm in diameter with a 0.45 mm pitch, tapped with a 2.05 mm drill; imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
LX9000 glider glide-computer panel screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | 10 mm | 0.45 mm | not stated | not stated | M2.5 x 10mm painted Nextel-finish instrument screw for glider instrument panels | Confirmed |
Fitment records and sources
M2.5 x 10mm painted Nextel-finish instrument screw for glider instrument panels
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2.5 x 10mm Phillips Wafer Head Screw for Turntable Cartridge Headshell Mount - Pack of 50 Black
$5.99 -
M2.5 x 10mm Phillips Wafer Head Screw for ASUS TUF Gaming A15/F15 Laptop Repair - Single Replacement Black
$0.10 each · min. 50
-
M2.5 x 10mm Phillips Wafer Head Screw for Laptop Bottom Cover Replacement - Single Replacement Black
$0.10 each · min. 50
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with LX9000 glider glide-computer panel screw, closest length match first.
- Marine compass bezel also M2.5 × 10 mm
- Audio MusiKraft cartridge/headshell mounting kit also M2.5 × 10 mm
- Audio MusiKraft cartridge mounting screw kit also M2.5 × 10 mm
- NVIDIA Jetson Nano Developer Kit carrier board also M2.5 × 10 mm
- Turntable headshell / phono cartridge mounting also M2.5 × 10 mm
- VinylPro aluminium cartridge kit also M2.5 × 10 mm
- Turntable headshell / phono cartridge mounting screws also M2.5 × 10 mm
- HP Compaq nc8430 also M2.5 × 10 mm
Questions about LX9000 glider glide-computer panel screw screws
- What size screw does LX9000 glider glide-computer panel screw use?
- M2.5 × 10 mm for M2.5 x 10mm painted Nextel-finish instrument screw for glider instrument panels.
- How long are the screws in LX9000 glider glide-computer panel screw?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for LX9000 glider glide-computer panel screw?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for LX9000 glider glide-computer panel screw?
- TechSpareWarehouse (our own store) lists M2.5 x 10mm, which matches the length in the records above.