NVIDIA Jetson Nano Developer Kit carrier board screw size
M2.5 · 6 to 10 mm long
Our records put NVIDIA Jetson Nano Developer Kit carrier board on M2.5 screws in lengths from 6 to 10 mm.
It is listed for winford Engineering DIN-rail mounting plate product page states the plate uses M2.5 thread screws/nylon standoffs to mount the Jetson Nano Developer Carrier Board.
This entry is marked confirmed and comes from winford.com.
An M2.5 screw is 2.5 mm in diameter with a 0.45 mm pitch, tapped with a 2.05 mm drill; imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
NVIDIA Jetson Nano Developer Kit carrier board screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | 6–10 mm | 0.45 mm | not stated | not stated | Winford Engineering DIN-rail mounting plate product page states the plate uses M2.5 thread screws/nylon standoffs to mount the Jetson Nano Developer Carrier Boardthread-locking patch | Confirmed |
Fitment records and sources
Winford Engineering DIN-rail mounting plate product page states the plate uses M2.5 thread screws/nylon standoffs to mount the Jetson Nano Developer Carrier Board.
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Where the manufacturer publishes a torque value, use a torque driver rather than feel.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- Nylon-coated M2.5 screws (ThinkPad Edge) are thread-locking; plain replacements work loose over time.
- Eurorack rail thread depends on rail brand: Vector/SynthRacks rails use M2.5, others use M3.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2.5 x 6mm Laptop Motherboard Replacement Screws Wafer Head 10-Pack Black
$4.99 -
10x M2.5 x 6mm Phillips Screws for Lenovo ThinkPad X131e Chromebook LCD Hinge
$4.99
-
M2.5 x 8mm Screws for Retevis RT27 Radio Belt Clip 10-Pack Black Phillips
$4.99 -
M2.5 x 8mm Screws for Raspberry Pi 5 Case and PoE HAT 10-Pack Black
$4.99 -
M2.5 x 10mm Phillips Wafer Head Screw for Turntable Cartridge Headshell Mount - Pack of 50 Black
$5.99 -
M2.5 x 10mm Phillips Wafer Head Screw for ASUS TUF Gaming A15/F15 Laptop Repair - Single Replacement Black
$0.10 each · min. 50
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with NVIDIA Jetson Nano Developer Kit carrier board, closest length match first.
- Fishing reel handle lock nut also M2.5 × 6–8 mm
- Turntable headshell / phono cartridge mounting also M2.5 × 6–10 mm
- VinylPro aluminium cartridge kit also M2.5 × 6–10 mm
- Turntable headshell / phono cartridge mounting screws also M2.5 × 6–10 mm
- Tonar cartridge screw set for phono cartridges also M2.5 × 6 mm
- Ortofon 2M cartridge also M2.5 × 6–7 mm
- Marine compass bezel also M2.5 × 6–10 mm
- LX9000 glider glide-computer panel screw also M2.5 × 10 mm
Questions about NVIDIA Jetson Nano Developer Kit carrier board screws
- What size screw does NVIDIA Jetson Nano Developer Kit carrier board use?
- M2.5 × 6–10 mm for winford Engineering DIN-rail mounting plate product page states the plate uses M2.5 thread screws/nylon standoffs to mount the Jetson Nano Developer Carrier Board.
- How long are the screws in NVIDIA Jetson Nano Developer Kit carrier board?
- The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for NVIDIA Jetson Nano Developer Kit carrier board?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for NVIDIA Jetson Nano Developer Kit carrier board?
- TechSpareWarehouse (our own store) lists M2.5 x 6mm, M2.5 x 8mm and M2.5 x 10mm, which match lengths in the records above.