NBK SSCZS-M1.4 captive pan head screw screw size
M1.4 · length not stated in the sources
The screws used on NBK SSCZS-M1.4 captive pan head screw are M1.4. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: captive (loss-prevention) machine screw for precision instruments and miniature sensor housings, M1.4 thread.
This entry is marked confirmed and comes from nbk1560.com.
An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
NBK SSCZS-M1.4 captive pan head screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | not stated | 0.3 mm | not stated | not stated | Captive (loss-prevention) machine screw for precision instruments and miniature sensor housings, M1.4 threadcaptive | Confirmed |
Fitment records and sources
Captive (loss-prevention) machine screw for precision instruments and miniature sensor housings, M1.4 thread
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Industrial parts lists usually give the full callout (thread, length, head, grade); match all four, not just the thread.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
More in Industrial & Machinery
The same screw also fits
Devices whose records share a thread with NBK SSCZS-M1.4 captive pan head screw, closest length match first.
- Eyeglass/spectacle hinge screws also M1.4
- NBK SPE-MC PEEK micro pan head screws also M1.4
- Slice Engineering Mosquito / Mosquito Conduct hotend also M1.4
- Eyeglass hinge repair screw also M1.4
- Compact & action cameras also M1.4
- Nintendo Switch Joy-Con also M1.4
- Dell Pro Max 18 Plus MB18250 also M1.4
- Dell 14 Premium DA14250 also M1.4
Questions about NBK SSCZS-M1.4 captive pan head screw screws
- What size screw does NBK SSCZS-M1.4 captive pan head screw use?
- M1.4 for captive (loss-prevention) machine screw for precision instruments and miniature sensor housings, M1.4 thread.
- How long are the screws in NBK SSCZS-M1.4 captive pan head screw?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for NBK SSCZS-M1.4 captive pan head screw?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.