NCR 5684/5685 ATM cabinetry screw size
M5 · 35 mm long
If you are replacing a screw on NCR 5684/5685 ATM cabinetry, the thread is M5, 35 mm long.
The record covers replacement part listing: '009-0003252, SCREW ALLEN CAP, M5 X 35 LONG, NCR 5684/5685 ATM, 5685 CABINETRY'.
Head and drive, as the source states them: Hex socket (Allen) drive.
This entry is marked confirmed and comes from gulentech-hk.com.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
NCR 5684/5685 ATM cabinetry screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 35 mm | 0.8 mm | not stated | Hex socket (Allen) | Replacement part listing: '009-0003252, SCREW ALLEN CAP, M5 X 35 LONG, NCR 5684/5685 ATM, 5685 CABINETRY' | Confirmed |
Fitment records and sources
Replacement part listing: '009-0003252, SCREW ALLEN CAP, M5 X 35 LONG, NCR 5684/5685 ATM, 5685 CABINETRY'
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Printers and POS terminals often use self-tapping screws into plastic; re-use the original thread path instead of cutting a new one.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 35 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Hex socket (Allen) drive. For comparison, standard M5 heads take PH2 (Phillips) or T25 (Torx), or a 4 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
More in Printers, POS & Office
The same screw also fits
Devices whose records share a thread with NCR 5684/5685 ATM cabinetry, closest length match first.
- LG 50PZ950 also M5 × 35 mm
- LG 55LV5500 also M5 × 35 mm
- Voron 2.4 / Trident also M5 × 35 mm
- LG 47LW6500 also M5 × 35 mm
- LG 55LW5700 also M5 × 35 mm
- Raymarine Axiom 7/9/12 multifunction display also M5 × 35 mm
- LG 50PZ750 also M5 × 35 mm
- LG 47LW7700 also M5 × 35 mm
Questions about NCR 5684/5685 ATM cabinetry screws
- What size screw does NCR 5684/5685 ATM cabinetry use?
- M5 × 35 mm for replacement part listing: '009-0003252, SCREW ALLEN CAP, M5 X 35 LONG, NCR 5684/5685 ATM, 5685 CABINETRY'.
- How long are the screws in NCR 5684/5685 ATM cabinetry?
- The record gives 35 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for NCR 5684/5685 ATM cabinetry?
- The source lists a Hex socket (Allen) drive. Standard M5 heads otherwise take PH2 (Phillips) or T25 (Torx), or a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.