Raymarine Axiom 7/9/12 multifunction display screw size
M5 · 16 to 58 mm long
Raymarine Axiom 7/9/12 multifunction display takes M5 metric screws in lengths from 16 to 58 mm.
The record covers flush/surface mount kit includes four M5 x 58 threaded studs; the trunnion adaptor is held by four M5 x 16 screws (4 mm hex).
This entry is marked confirmed and comes from productimageserver.com.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Raymarine Axiom 7/9/12 multifunction display screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 16–58 mm | 0.8 mm | not stated | not stated | Flush/surface mount kit includes four M5 x 58 threaded studs; the trunnion adaptor is held by four M5 x 16 screws (4 mm hex) | Confirmed |
Fitment records and sources
Flush/surface mount kit includes four M5 x 58 threaded studs; the trunnion adaptor is held by four M5 x 16 screws (4 mm hex)
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 16–58 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- The 'GoPro thread' is M5-0.8, a de facto standard on third-party mounts, and is not the imperial 1/4-20 tripod thread.
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with Raymarine Axiom 7/9/12 multifunction display, closest length match first.
- Arcade cabinet CRT monitor chassis mount (Nintendo/table & upright cabinets) also M5 × 16 mm
- LG 55LW5700 also M5 × 35 mm
- LG 47LW7700 also M5 × 35 mm
- ATV plastics and fenders also M5 × 16 mm
- LG 50PZ750 also M5 × 35 mm
- LG 47LW6500 also M5 × 35 mm
- StarTech Universal Projector Wall Mount (PROJWALLMNT) also M5 × 24 mm
- LG 55LV5500 also M5 × 35 mm
Questions about Raymarine Axiom 7/9/12 multifunction display screws
- What size screw does Raymarine Axiom 7/9/12 multifunction display use?
- M5 × 16–58 mm for flush/surface mount kit includes four M5 x 58 threaded studs; the trunnion adaptor is held by four M5 x 16 screws (4 mm hex).
- How long are the screws in Raymarine Axiom 7/9/12 multifunction display?
- The records range from 16 to 58 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Raymarine Axiom 7/9/12 multifunction display?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.