Nintendo Switch shield plate screw size
M2 · 3 mm long
If you are replacing a screw on Nintendo Switch shield plate, the thread is M2, 3 mm long.
Where it is used: shield plate retention screws.
This entry is marked reported and comes from ifixit.com.
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
Nintendo Switch shield plate screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Shield plate retention screws | Reported |
Fitment records and sources
Shield plate retention screws
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Phone and wearable screws are tiny and often differ by fractions of a millimetre between positions; keep each one next to the hole it came from.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 3 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Phones, Tablets & Wearables
Akuvox A08 video doorbellAkuvox A08 video doorbell (back plate)Anbernic RG35XX rear case screwsApple Watch case screwsApple Watch strap adapterASUS ROG Ally (RC71L)Asus ROG Ally (RC71L) back panel and M.2 2230 SSD coverASUS ROG Ally RC71L rear shellCompact smart sensor PCBsDive watch bezel insertDive watch bezelsExtech 407732 sound level meter battery cover screw
Browse all 134 in Phones, Tablets & Wearables →The same screw also fits
Devices whose records share a thread with Nintendo Switch shield plate, closest length match first.
- Steam Deck / OLED SSD retention also M2 × 3 mm
- Asus ROG Ally (RC71L) back panel and M.2 2230 SSD cover also M2 × 3 mm
- Nintendo Switch OLED motherboard also M2 × 3 mm
- Valve Steam Deck (LCD) also M2 × 3 mm
- Nintendo Switch mainboard also M2 × 3 mm
- Nintendo Switch microSD reader also M2 × 3 mm
- Steam Deck internal M.2 2230 SSD screw also M2 × 3 mm
- ROG Ally internal chassis also M2 × 3 mm
Questions about Nintendo Switch shield plate screws
- What size screw does Nintendo Switch shield plate use?
- M2 × 3 mm for shield plate retention screws.
- How long are the screws in Nintendo Switch shield plate?
- The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Nintendo Switch shield plate?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Nintendo Switch shield plate?
- TechSpareWarehouse (our own store) lists M2 x 3mm, which matches the length in the records above.