Rad Power Bikes RadMini 4 screw size
M6 · 20 to 25 mm long
Our records put Rad Power Bikes RadMini 4 on M6 screws in lengths from 20 to 25 mm.
Where it is used: screw for the front rack installation.
This entry is marked confirmed and comes from forums.electricbikereview.com.
For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Rad Power Bikes RadMini 4 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 20–25 mm | 1 mm | not stated | not stated | Screw for the front rack installation | Confirmed |
Fitment records and sources
Screw for the front rack installation.
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 20–25 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Rack hole threads vary: 10-32 and 12-24 are still common in US racks alongside M6 - check the rail before buying.
- Server rack cage nuts come in M4/M5/M6 for the same square hole — confirm what your rails and equipment ears use.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Rad Power Bikes RadMini 4, closest length match first.
- BMW Hexhead/K-Bike/Oilhead EnDuraLast charging-system component screw also M6 × 22 mm
- Industrial machinery also M6 × 20–25 mm
- Weight machine adjustment brackets also M6 × 20–25 mm
- VELA Samba 150 Dental Chair also M6 × 25 mm
- Car license plate also M6 × 20 mm
- MikroTik MTAD-5G-30D3-PA parabolic dish also M6 × 20 mm
- FJD 3D Excavator Guidance System (GNSS/IMU hardware) also M6 × 20–25 mm
- RF Elements Twin Horn antenna bracket also M6 × 20 mm
Questions about Rad Power Bikes RadMini 4 screws
- What size screw does Rad Power Bikes RadMini 4 use?
- M6 × 20–25 mm for screw for the front rack installation.
- How long are the screws in Rad Power Bikes RadMini 4?
- The records range from 20 to 25 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Rad Power Bikes RadMini 4?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.