Schaerer Coffee Art Plus espresso machine screw size
M3 · length not stated in the sources
Schaerer Coffee Art Plus espresso machine takes M3 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers OEM screw part 3371001012 specified as M3.
This entry is marked confirmed and comes from partstown.ca.
M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Schaerer Coffee Art Plus espresso machine screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | OEM screw part 3371001012 specified as M3 | Confirmed |
Fitment records and sources
OEM screw part 3371001012 specified as M3
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Unplug the appliance and discharge any capacitors before removing covers.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Label printer parts lists write M3*6 with an asterisk; that is still a true ISO M3 x 6mm machine screw.
- Power-tool gearcase and clamshell screws are usually thread-forming (marked "ST") even when the parts list gives an M-size — a normal machine screw of the same size may not hold in the plastic boss.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Appliances & HVAC
The same screw also fits
Devices whose records share a thread with Schaerer Coffee Art Plus espresso machine, closest length match first.
- OE Lido / Fixie hand coffee grinder also M3
- Samsung vacuum cleaner also M3
- Coffee machine control panel also M3
- Daikin FTXS/CTXS Mini-split control board / cover screw also M3
- Vulcan-Hart Chef combi oven also M3
- Dyson filter cap and battery cover also M3
- Microwave door latch and hinge also M3
- Dell U2719D also M3
Questions about Schaerer Coffee Art Plus espresso machine screws
- What size screw does Schaerer Coffee Art Plus espresso machine use?
- M3 for OEM screw part 3371001012 specified as M3.
- How long are the screws in Schaerer Coffee Art Plus espresso machine?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Schaerer Coffee Art Plus espresso machine?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.