What size screw does Sonos One power receptacle use?

M3 × 6 mm for power adapter bracket screws.

How long are the screws in Sonos One power receptacle?

The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Sonos One power receptacle?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Sonos One power receptacle?

TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.

Sonos One power receptacle screw size

M3 · 6 mm long

Sonos One power receptacle takes M3 metric screws, 6 mm long.

It is listed for power adapter bracket screws.

This entry is marked confirmed and comes from ifixit.com.

M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Sonos One power receptacle screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	6 mm	0.5 mm	not stated	not stated	Power adapter bracket screws	Confirmed

Fitment records and sources

M36mmconfirmed

Power adapter bracket screws

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

Sonos speakers mix lengths within one unit — M3 for driver housings, M2.5 at the control panel. Keep them sorted during teardown.
LED strip clips strip easily — M3x12 into thin plastic should be hand-driven, never with a power driver.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Displays, TVs & Mounts

27-34in ultrawide monitors 3D printer electronics 51.2V 280Ah battery pack concealed carry handle Accuracy International AICS chassis stockside securing screws Acer / ASUS / BenQ monitors Acer Predator X34 Acer XR342CK AGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) drivers Amazon Echo Dot internals Amico patient monitor 5-inch shelf with VESA plate

Browse all 388 in Displays, TVs & Mounts →

The same screw also fits

Devices whose records share a thread with Sonos One power receptacle, closest length match first.

Dell P2018H also M3 × 6 mm
Dell S3220DGF also M3 × 6 mm
HP P24h G4 also M3 × 6 mm
Dell P2016 also M3 × 6 mm
Dell U2312H also M3 × 6 mm
Dell Pro 27 Plus monitor (P2725D/DE/QE) also M3 × 6 mm
Dell SP2318H also M3 × 6 mm
Dell P2014H also M3 × 6 mm

Questions about Sonos One power receptacle screws

What size screw does Sonos One power receptacle use?: M3 × 6 mm for power adapter bracket screws.
How long are the screws in Sonos One power receptacle?: The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Sonos One power receptacle?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Sonos One power receptacle?: TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.

Heads up: shipping delay