Tiny Whoop / micro FPV drone flight controller & ESC mounting screws screw size
M1.4 · 6 to 10 mm long
The screws used on Tiny Whoop / micro FPV drone flight controller & ESC mounting screws are M1.4 in lengths from 6 to 10 mm.
It is listed for rotorama product page: 'Self-tapping screws with size M1.4 and cross head... suitable for installing flight controller on Tinywhoop frame'.
Head and drive, as the source states them: Phillips drive.
This entry is marked confirmed and comes from rotorama.com.
M1.4 means a 1.4 mm nominal diameter with a 0.3 mm thread pitch. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Tiny Whoop / micro FPV drone flight controller & ESC mounting screws screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 6–10 mm | 0.3 mm | not stated | Phillips | Rotorama product page: 'Self-tapping screws with size M1.4 and cross head... suitable for installing flight controller on Tinywhoop frame'self-tapping / thread-forming | Confirmed |
Fitment records and sources
Rotorama product page: 'Self-tapping screws with size M1.4 and cross head... suitable for installing flight controller on Tinywhoop frame'
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Vibration loosens small screws on drones and RC models, so builders commonly add a drop of medium (blue) threadlocker on metal-to-metal joints — never on plastic.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- Whoop drone M1.4 comes in steel, PEEK and RENY versions: plastic ones are for cameras, not structural frame use.
- Whoop motor screws differ between M1.4x3mm and M1.6x4mm across BetaFPV/NewBeeDrone product generations — check the exact model.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M1.4 Phillips Flat Head Carbon Steel Machine Screws (Multiple Lengths & Finishes)
$5.00Choose size -
M1.4 x 3mm Black Wafer Head Battery Lock Screws for Sennheiser MKH800, SK6000 & SK5012 – 20-Pack Replacement
$4.99Choose size -
M1.6 Phillips Flat Head Carbon Steel Machine Screws (Multiple Lengths & Finishes)
$0.05Choose size -
M1.6 Phillips Flat Head Carbon Steel Machine Screws (Multiple Lengths & Finishes) | 50-Pack
From $4.99Choose size
More in Drones, RC & Gimbals
The same screw also fits
Devices whose records share a thread with Tiny Whoop / micro FPV drone flight controller & ESC mounting screws, closest length match first.
- FPV flight-controller / ESC stacks also M1.4 × 6–8 mm
- Self-aligning spring hinge screw (Tabco Optical) also M1.4 × 6.1–10 mm
- Dell Precision 5760 also M1.4 × 6.3 mm
- NBK SPE-MC PEEK micro pan head screws also M1.4 × 6 mm
- Binocular hinge / bridge also M1.4 × 6–8 mm
- DIN 912 socket-head cap screw (smallest size) also M1.4 × 6–10 mm
- Bredent dental prosthetic screw also M1.4 × 6–8 mm
- Miniature precision instrument screws (NBK) also M1.4 × 6–10 mm
Questions about Tiny Whoop / micro FPV drone flight controller & ESC mounting screws screws
- What size screw does Tiny Whoop / micro FPV drone flight controller & ESC mounting screws use?
- M1.4 × 6–10 mm for rotorama product page: 'Self-tapping screws with size M1.4 and cross head... suitable for installing flight controller on Tinywhoop frame'.
- How long are the screws in Tiny Whoop / micro FPV drone flight controller & ESC mounting screws?
- The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Tiny Whoop / micro FPV drone flight controller & ESC mounting screws?
- The source lists a Phillips drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.