Tonar cartridge screw set for phono cartridges screw size
M2.5 · 3 to 6 mm long
Tonar cartridge screw set for phono cartridges takes M2.5 metric screws in lengths from 3 to 6 mm.
It is listed for 'Screw type: M2.5 non-magnetic hardware, Lengths included: 3/6...' for mounting phono cartridges to headshells.
This entry is marked confirmed and comes from soundium.com.
An M2.5 screw is 2.5 mm in diameter with a 0.45 mm pitch, tapped with a 2.05 mm drill; imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
Tonar cartridge screw set for phono cartridges screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | 3–6 mm | 0.45 mm | not stated | not stated | 'Screw type: M2.5 non-magnetic hardware, Lengths included: 3/6...' for mounting phono cartridges to headshells | Confirmed |
Fitment records and sources
'Screw type: M2.5 non-magnetic hardware, Lengths included: 3/6...' for mounting phono cartridges to headshells
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Where the manufacturer publishes a torque value, use a torque driver rather than feel.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- M2 and M2.5 are both marketed for turntable headshells; buyers must check which their specific cartridge/tonearm brand uses.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
25x M2.5 x 3mm Phillips Screws for Acer Nitro 5 SSD M.2 WiFi Card
$5.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 Display Hinge 10-Pack Black
$4.99 -
M2.5 x 4mm Screws for Lenovo IdeaPad 5 Pro 14 System Board Hinge 10-Pack Black
$4.99
-
M2.5 x 5mm Screws Compatible with Dell XPS 14 9440 Display Assembly 10-Pack
$4.99 -
M2.5 x 5mm Phillips Wafer Head Screw for Action Camera Protective Housing - Pack of 50 Black
$4.79 each · min. 2
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
M2.5 x 3mm Phillips Wafer Head Screws, Low Profile – 10-Pack Black
$4.99Choose size
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with Tonar cartridge screw set for phono cartridges, closest length match first.
- Turntable headshell / phono cartridge mounting screws also M2.5 × 3–6 mm
- Ortofon 2M cartridge also M2.5 × 5–6 mm
- NVIDIA Jetson Nano Developer Kit carrier board also M2.5 × 6 mm
- Fishing reel handle lock nut also M2.5 × 5–6 mm
- VinylPro aluminium cartridge kit also M2.5 × 6 mm
- Turntable headshell / phono cartridge mounting also M2.5 × 3–6 mm
- Turntable cartridge mounting kit (retail) also M2.5 × 3–6 mm
- Dive computer strap / bezel also M2.5 × 3–6 mm
Questions about Tonar cartridge screw set for phono cartridges screws
- What size screw does Tonar cartridge screw set for phono cartridges use?
- M2.5 × 3–6 mm for 'Screw type: M2.5 non-magnetic hardware, Lengths included: 3/6...' for mounting phono cartridges to headshells.
- How long are the screws in Tonar cartridge screw set for phono cartridges?
- The records range from 3 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for Tonar cartridge screw set for phono cartridges?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Tonar cartridge screw set for phono cartridges?
- TechSpareWarehouse (our own store) lists M2.5 x 3mm, M2.5 x 4mm and M2.5 x 5mm, which match lengths in the records above.