TV wall mount, VESA 200x200 and larger screw size
M6 · 12 to 20 mm long
Our records put TV wall mount, VESA 200x200 and larger on M6 screws in lengths from 12 to 20 mm.
The record covers M6 is standard on 200x200 and bigger patterns.
This entry is marked reported and comes from electronics.alibaba.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
TV wall mount, VESA 200x200 and larger screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 12–20 mm | 1 mm | not stated | not stated | M6 is standard on 200x200 and bigger patterns | Reported |
Fitment records and sources
M6 is standard on 200x200 and bigger patterns
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 12–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
- VESA displays over 50kg move up to M8 x 1.25, which is outside metric M6 hardware - don't force an M6 bolt into a heavy-panel mount.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with TV wall mount, VESA 200x200 and larger, closest length match first.
- ASUS VG27UQ1A also M6 × 16.2 mm
- ASUS VG27AQA1A also M6 × 16.2 mm
- ASUS BE27ACSBK also M6 × 16.5 mm
- ASUS VG32VQ1A also M6 × 16.2 mm
- VESA 200x200 and larger (MIS-E/F) also M6 × 12–20 mm
- TCL & Vizio 43-55in TVs also M6 × 12–16 mm
- ASUS VG32VQL1A also M6 × 16.2 mm
- LG TVs 43-55in also M6 × 12–14 mm
Questions about TV wall mount, VESA 200x200 and larger screws
- What size screw does TV wall mount, VESA 200x200 and larger use?
- M6 × 12–20 mm for M6 is standard on 200x200 and bigger patterns.
- How long are the screws in TV wall mount, VESA 200x200 and larger?
- The records range from 12 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for TV wall mount, VESA 200x200 and larger?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.