VESA 75x75 & 100x100 (MIS-D) screw size
M4 · 10 to 12 mm long
Our records put VESA 75x75 & 100x100 (MIS-D) on M4 screws in lengths from 10 to 12 mm.
It is listed for the VESA standard specifies M4 for these patterns.
This entry is marked confirmed and comes from en.wikipedia.org.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
VESA 75x75 & 100x100 (MIS-D) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10–12 mm | 0.7 mm | not stated | not stated | the VESA standard specifies M4 for these patterns | Confirmed |
Fitment records and sources
the VESA standard specifies M4 for these patterns
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–12 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- VESA thread size is set by pattern class: M4 for 75x75/100x100, M6 or M8 for the big 200mm+ patterns. Check the plate on the back of the display.
- VESA size follows the hole pattern, not the brand: MIS-D uses M4, MIS-E/F uses M6 or M8.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Chainsaw & Cut-off Saw Screws for STIHL MS 460, MS 362, TS480i & TS500i (IS-M4x12) – 10-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Monitor VESA, Neck & Stand Screws for Dell UltraSharp U4320Q & Sceptre Monitors – 8-Pack Replacement
$5.49Choose size
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with VESA 75x75 & 100x100 (MIS-D), closest length match first.
- MSI MAG 275UPD E14 also M4 × 10 mm
- Dell P2217H also M4 × 10 mm
- Dell P2719H also M4 × 10 mm
- Dell P2717H also M4 × 10 mm
- Atdec Telehook TH-2250-VF display wall mount also M4 × 12 mm
- LG 47LK550 also M4 × 12 mm
- LG 47LW5600 also M4 × 12 mm
- LG 42LK550 also M4 × 12 mm
Questions about VESA 75x75 & 100x100 (MIS-D) screws
- What size screw does VESA 75x75 & 100x100 (MIS-D) use?
- M4 × 10–12 mm for the VESA standard specifies M4 for these patterns.
- How long are the screws in VESA 75x75 & 100x100 (MIS-D)?
- The records range from 10 to 12 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for VESA 75x75 & 100x100 (MIS-D)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.