VESA MIS-D display mount (75x75 / 100x100) screw size
M4 · 8 to 10 mm long
The screws used on VESA MIS-D display mount (75x75 / 100x100) are M4 in lengths from 8 to 10 mm.
Where it is used: VESA flat display mounting interface for small/medium displays.
This entry is marked confirmed and comes from vesa.org.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
VESA MIS-D display mount (75x75 / 100x100) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8–10 mm | 0.7 mm | not stated | not stated | VESA flat display mounting interface for small/medium displays | Confirmed |
Fitment records and sources
VESA flat display mounting interface for small/medium displays
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 8–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- VESA thread size is set by pattern class: M4 for 75x75/100x100, M6 or M8 for the big 200mm+ patterns. Check the plate on the back of the display.
- Display mounts mix systems: the screen side is metric M4/M6, but the wall side of many mounts uses imperial wood screws such as #14 x 2.5in.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with VESA MIS-D display mount (75x75 / 100x100), closest length match first.
- Dell U2913WM also M4 × 10 mm
- LG 28TK420S also M4 × 10 mm
- TV wall mount, VESA 75/100 also M4 × 10 mm
- VESA MIS-C displays (8-11.9 inch) also M4 × 8 mm
- Dell SP2418H also M4 × 10 mm
- Dell E2414H also M4 × 10 mm
- Havis DM-10-112 display mount base also M4 × 10 mm
- Dell P2217WH also M4 × 10 mm
Questions about VESA MIS-D display mount (75x75 / 100x100) screws
- What size screw does VESA MIS-D display mount (75x75 / 100x100) use?
- M4 × 8–10 mm for VESA flat display mounting interface for small/medium displays.
- How long are the screws in VESA MIS-D display mount (75x75 / 100x100)?
- The records range from 8 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for VESA MIS-D display mount (75x75 / 100x100)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.