VESA MIS-E display mount screw size
M4 · 8 to 12 mm long
Our records put VESA MIS-E display mount on M4 screws in lengths from 8 to 12 mm.
Where it is used: MIS-E pattern (200x100mm class) also uses M4 threaded inserts per FDMI.
This entry is marked reported and comes from glenwing.github.io.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
VESA MIS-E display mount screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8–12 mm | 0.7 mm | not stated | not stated | MIS-E pattern (200x100mm class) also uses M4 threaded inserts per FDMI | Reported |
Fitment records and sources
MIS-E pattern (200x100mm class) also uses M4 threaded inserts per FDMI
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 8–12 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- VESA thread size is set by pattern class: M4 for 75x75/100x100, M6 or M8 for the big 200mm+ patterns. Check the plate on the back of the display.
- VESA size follows the hole pattern, not the brand: MIS-D uses M4, MIS-E/F uses M6 or M8.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Chainsaw & Cut-off Saw Screws for STIHL MS 460, MS 362, TS480i & TS500i (IS-M4x12) – 10-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Monitor VESA, Neck & Stand Screws for Dell UltraSharp U4320Q & Sceptre Monitors – 8-Pack Replacement
$5.49Choose size
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with VESA MIS-E display mount, closest length match first.
- Dell P2212H also M4 × 10 mm
- LG 47LW6500 also M4 × 12 mm
- Samsung monitors & smaller TVs also M4 × 8–12 mm
- Dell P2815Q also M4 × 10 mm
- Samsung TV pedestal stand (19-22in) also M4 × 10 mm
- Dell P2714H also M4 × 10 mm
- LG 50PZ750 also M4 × 12 mm
- LG 47LW7700 also M4 × 12 mm
Questions about VESA MIS-E display mount screws
- What size screw does VESA MIS-E display mount use?
- M4 × 8–12 mm for MIS-E pattern (200x100mm class) also uses M4 threaded inserts per FDMI.
- How long are the screws in VESA MIS-E display mount?
- The records range from 8 to 12 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for VESA MIS-E display mount?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.