VESA MIS-F large display mount screw size
M6 · 10 to 20 mm long
The screws used on VESA MIS-F large display mount are M6 in lengths from 10 to 20 mm.
Where it is used: large patterns (200x200 up to 400x400mm) use M6 or M8 threads; check the display's rating plate.
This entry is marked reported and comes from glenwing.github.io.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
VESA MIS-F large display mount screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 10–20 mm | 1 mm | not stated | not stated | Large patterns (200x200 up to 400x400mm) use M6 or M8 threads; check the display's rating plate | Reported |
Fitment records and sources
Large patterns (200x200 up to 400x400mm) use M6 or M8 threads; check the display's rating plate
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
- VESA displays over 50kg move up to M8 x 1.25, which is outside metric M6 hardware - don't force an M6 bolt into a heavy-panel mount.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with VESA MIS-F large display mount, closest length match first.
- Pro-AV truss clamps also M6 × 16–20 mm
- 27-34in ultrawide monitors also M6 × 12–16 mm
- Signage standoffs also M6 × 20 mm
- StarTech Universal Projector Wall Mount (PROJWALLMNT) also M6 × 10–20 mm
- ASUS VG27AQ1A also M6 × 16.2 mm
- Speaker flying frame / eyebolt hardware also M6 × 20 mm
- ASUS VG27AQL1A also M6 × 16.2 mm
- Larger flat-panel TVs (VESA interface) also M6 × 12 mm
Questions about VESA MIS-F large display mount screws
- What size screw does VESA MIS-F large display mount use?
- M6 × 10–20 mm for large patterns (200x200 up to 400x400mm) use M6 or M8 threads; check the display's rating plate.
- How long are the screws in VESA MIS-F large display mount?
- The records range from 10 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for VESA MIS-F large display mount?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.