How long are the screws in Samsung range / wall oven?

The records range from 10 to 20 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M4 screw?

0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.

What screwdriver do I need for Samsung range / wall oven?

The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.

Can I use an imperial screw instead of M4?

No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.

Samsung range / wall oven screw size

M4 · 10 to 20 mm long

Our records put Samsung range / wall oven on M4 screws in lengths from 10 to 20 mm.

The record covers OEM oven/range screws explicitly labeled M4: 'Screw-Tapping;Th,+,2S,M4,L10' (6002-000558, range), 'Screw-Tapping;Fh,+,2S,M4' (6002-001316, wall oven), 'Screw-Machine;Th,+,M4,L10' (6001-003234, wall oven).

This entry is marked confirmed and comes from appliancepartspros.com.

For reference, M4 is 4 mm across the threads at 0.7 mm pitch. The imperial size people confuse it with: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.

Samsung range / wall oven screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M4	10–20 mm	0.7 mm	not stated	not stated	OEM oven/range screws explicitly labeled M4: 'Screw-Tapping;Th,+,2S,M4,L10' (6002-000558, range), 'Screw-Tapping;Fh,+,2S,M4' (6002-001316, wall oven), 'Screw-Machine;Th,+,M4,L10' (6001-003234, wall oven)	Confirmed

Fitment records and sources

M4L10-L20mmconfirmed

OEM oven/range screws explicitly labeled M4: 'Screw-Tapping;Th,+,2S,M4,L10' (6002-000558, range), 'Screw-Tapping;Fh,+,2S,M4' (6002-001316, wall oven), 'Screw-Machine;Th,+,M4,L10' (6001-003234, wall oven)

pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20

Source

How to check the screw before you buy

VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 10–20 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.

Common mix-ups with M4

Display mounts mix systems: the screen side is metric M4/M6, but the wall side of many mounts uses imperial wood screws such as #14 x 2.5in.
Water heater elements use pipe threads (NPSM/NPT), not metric machine screws.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Displays, TVs & Mounts

27-34in ultrawide monitors 3D printer electronics 51.2V 280Ah battery pack concealed carry handle Accuracy International AICS chassis stockside securing screws Acer / ASUS / BenQ monitors Acer Predator X34 Acer XR342CK AGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) drivers Amazon Echo Dot internals Amico patient monitor 5-inch shelf with VESA plate

Browse all 388 in Displays, TVs & Mounts →

The same screw also fits

Devices whose records share a thread with Samsung range / wall oven, closest length match first.

Samsung TV pedestal stand (24-55in) also M4 × 14 mm
Dell P1917S also M4 × 10 mm
LG 43LJ5000 also M4 × 10 mm
Dell U2417HJ also M4 × 10 mm
LG 60PZ750 also M4 × 12 mm
Dell U2518D also M4 × 10 mm
Dell P2421D also M4 × 10 mm
ASUS PG32UCDM also M4 × 10 mm

Questions about Samsung range / wall oven screws

What size screw does Samsung range / wall oven use?: M4 × 10–20 mm for OEM oven/range screws explicitly labeled M4: 'Screw-Tapping;Th,+,2S,M4,L10' (6002-000558, range), 'Screw-Tapping;Fh,+,2S,M4' (6002-001316, wall oven), 'Screw-Machine;Th,+,M4,L10' (6001-003234, wall oven).
How long are the screws in Samsung range / wall oven?: The records range from 10 to 20 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M4 screw?: 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
What screwdriver do I need for Samsung range / wall oven?: The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
Can I use an imperial screw instead of M4?: No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.

Heads up: shipping delay