ATV plastics and fenders screw size
M5 · 10 to 16 mm long
The screws used on ATV plastics and fenders are M5 in lengths from 10 to 16 mm.
The record covers fender and panel fasteners.
This entry is marked reported.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
ATV plastics and fenders screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 10–16 mm | 0.8 mm | not stated | not stated | Fender and panel fasteners | Reported |
Fitment records and sources
Fender and panel fasteners
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Stacking frame + rack tab + fender stay needs 18-20mm bolts, not the 12-16mm that come with a cage.
- Espresso/coffee-equipment M5 and M6 socket-head screws (DIN 7984/UNI 9327) are cross-brand standard fasteners shared across CMA, Astoria, and La Cimbali brewing-group hardware, so a single screw often services multiple manufacturers' machines.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with ATV plastics and fenders, closest length match first.
- LG 47LW7700 also M5 × 14.5 mm
- LG 50PZ750 also M5 × 14.5 mm
- Arcade cabinet CRT monitor chassis mount (Nintendo/table & upright cabinets) also M5 × 16 mm
- Raymarine Axiom 7/9/12 multifunction display also M5 × 16 mm
- LG 55LW5700 also M5 × 14.5 mm
- Panasonic TC-L65E60 also M5 × 15 mm
- LG 47LW6500 also M5 × 14.5 mm
- LG 55LV5500 also M5 × 14.5 mm
Questions about ATV plastics and fenders screws
- What size screw does ATV plastics and fenders use?
- M5 × 10–16 mm for fender and panel fasteners.
- How long are the screws in ATV plastics and fenders?
- The records range from 10 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for ATV plastics and fenders?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.