BenQ DV01K camera mount (RE04 series displays) screw size
M3 · 6 mm long
If you are replacing a screw on BenQ DV01K camera mount (RE04 series displays), the thread is M3, 6 mm long.
Where it is used: camera mount bracket screws to interactive display.
This entry is marked confirmed and comes from benq.eu.
M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
BenQ DV01K camera mount (RE04 series displays) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 6 mm | 0.5 mm | not stated | not stated | camera mount bracket screws to interactive display | Confirmed |
Fitment records and sources
camera mount bracket screws to interactive display
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Camera tripod and Arca threads are imperial 1/4-20 and 3/8-16, never M3.
- Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M3 x 6mm Replacement Screws for XLR Audio Connectors Phillips Wafer Head 50-Pack
$4.99 -
M3 x 6mm Phillips Wafer Head Carbon Steel Machine Screws for XLR Audio Connectors | 50-Pack (Black)
$4.99
-
M3 x 6mm Phillips Wafer Head Screw for 3D Printer Frame Assembly - Single Replacement Black
$0.10 each · min. 50
-
M3 x 6mm Phillips Wafer Head Screw for Boutique Guitar Pedal Enclosure - Single Replacement Black
$0.10 each · min. 50
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with BenQ DV01K camera mount (RE04 series displays), closest length match first.
- Dell UP2720Q also M3 × 6 mm
- Dell U2415 also M3 × 6 mm
- Dell U2719DC also M3 × 6 mm
- Dell U2413 also M3 × 6 mm
- Dell S2719HS also M3 × 6 mm
- HP P22h G5 also M3 × 6 mm
- HP P22h G4 also M3 × 6 mm
- Dell U2717DA also M3 × 6 mm
Questions about BenQ DV01K camera mount (RE04 series displays) screws
- What size screw does BenQ DV01K camera mount (RE04 series displays) use?
- M3 × 6 mm for camera mount bracket screws to interactive display.
- How long are the screws in BenQ DV01K camera mount (RE04 series displays)?
- The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for BenQ DV01K camera mount (RE04 series displays)?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for BenQ DV01K camera mount (RE04 series displays)?
- TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.