HP P22h G4 screw size
M2 / M3 / M4 · 3 to 10 mm long
The screws used on HP P22h G4 are M2, M3 and M4 in lengths from 3 to 10 mm.
There are 5 separate fitment records for it, including stand (qty 1, silver) (M2), back cover (black) (M3) and stand (silver) (M3), plus 2 more in the table below.
5 of the 5 records are marked confirmed, drawn from 1 source (h10032.www1.hp.com).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP P22h G4 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Stand (qty 1, silver) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Back cover (black)black finish | Confirmed |
| M3 | 5 mm | 0.5 mm | not stated | not stated | Stand (silver) | Confirmed |
| M3 | 6 mm | 0.5 mm | not stated | not stated | Stand (black)black finish | Confirmed |
| M4 | 10 mm | 0.7 mm | not stated | not stated | Stand (black)black finish | Confirmed |
Fitment records and sources
Stand (qty 1, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Back cover (black)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Stand (silver)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Stand (black)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Stand (black)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M3 / M4, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M3 / M4
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
- Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M3 x 4mm Phillips Wafer Head Screws for 2.5 SATA SSD Mounting 10-Pack
$4.99 -
M3 x 4mm Screws for Installing SSD into Synology NAS 10-Pack
$4.99 -
M3 x 5mm Phillips Wafer Head Screw for Electronics & Project Box Repair - Pack of 50 Black
$4.79 each · min. 2
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with HP P22h G4, closest length match first.
- HP P22h G5 also M2 × 3 mm
- Samsung PC490-ZA TV stand also M4 × 10 mm
- Dell U2719DS also M3 × 6 mm
- Dell U2717DA also M3 × 6 mm
- Dell S2719HS also M3 × 6 mm
- Dell P1917SWH also M3 × 6 mm
- Dell S2415H also M3 × 6 mm
- Dell U2417H also M3 × 6 mm
Questions about HP P22h G4 screws
- What size screw does HP P22h G4 use?
- M2 × 3 mm for stand (qty 1, silver); M3 × 4 mm for back cover (black); M3 × 5 mm for stand (silver); M3 × 6 mm for stand (black); M4 × 10 mm for stand (black).
- How long are the screws in HP P22h G4?
- The records range from 3 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP P22h G4?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP P22h G4?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M3 x 4mm and M3 x 5mm, which match lengths in the records above.