Bosch Intuvia 100 e-bike display mounting plate screw size
M3 · 22 mm long
Our records put Bosch Intuvia 100 e-bike display mounting plate on M3 screws, 22 mm long.
Where it is used: bosch Intuvia 100 mounting plate replacement screw, sold as genuine Bosch fastener.
This entry is marked confirmed and comes from 365cycles.com.
M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Bosch Intuvia 100 e-bike display mounting plate screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 22 mm | 0.5 mm | not stated | not stated | Bosch Intuvia 100 mounting plate replacement screw, sold as genuine Bosch fastener | Confirmed |
Fitment records and sources
Bosch Intuvia 100 mounting plate replacement screw, sold as genuine Bosch fastener
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 22 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
- The bioprinter M3 reference is a tube-connector thread spec, not a structural chassis screw; verify before assuming interchangeability with fastener screws.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Bosch Intuvia 100 e-bike display mounting plate, closest length match first.
- Prusa MK4 Nextruder also M3 × 22 mm
- Ultimaker Original heated bed / Z-stage upgrade kit also M3 × 22 mm
- Wurth Elektronik WA-SPAIE plastic spacer stud also M3 × 22 mm
- Bambu Lab X1/P1 heatbed transport anchors also M3 × 22 mm
- FPV flight-controller / ESC stacks also M3 × 22 mm
- PC watercooling radiator fan screws also M3 × 22 mm
- FPV carbon frame arms and standoffs also M3 × 22 mm
- HP LaserJet family common hardware also M3 × 22 mm
Questions about Bosch Intuvia 100 e-bike display mounting plate screws
- What size screw does Bosch Intuvia 100 e-bike display mounting plate use?
- M3 × 22 mm for bosch Intuvia 100 mounting plate replacement screw, sold as genuine Bosch fastener.
- How long are the screws in Bosch Intuvia 100 e-bike display mounting plate?
- The record gives 22 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Bosch Intuvia 100 e-bike display mounting plate?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.