Dashcam suction mount ball joint (large) screw size
M6 · 6 to 10 mm long
Our records put Dashcam suction mount ball joint (large) on M6 screws in lengths from 6 to 10 mm.
The record covers CH01B universal tripod ball mount offered with M4 or M6 screw joint.
This entry is marked reported and comes from ydboffer.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Dashcam suction mount ball joint (large) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 6–10 mm | 1 mm | not stated | not stated | CH01B universal tripod ball mount offered with M4 or M6 screw joint | Reported |
Fitment records and sources
CH01B universal tripod ball mount offered with M4 or M6 screw joint
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Where the manufacturer publishes a torque value, use a torque driver rather than feel.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Mic stand threads (5/8-27) and tripod threads (1/4-20, 3/8-16) are imperial, not metric — only accessory clips like Gravity's M6 adapter are genuinely M6.
- The same StarTech universal projector mount ships with M3, M4, M5, and M6 screw sets simultaneously so the installer can pick whichever matches the projector's own threaded inserts — metric size is projector-dependent, not mount-dependent.
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with Dashcam suction mount ball joint (large), closest length match first.
- Gas grill control panel also M6 × 10 mm
- Car license plate U-clip retaining fasteners (trim) also M6 × 10 mm
- Motorcycle side panels and tail cowl also M6 × 10 mm
- HIWIN QHH35 / QEH25 / QWH27 linear guideway fixing screws also M6 × 6–9 mm
- Philips 15210B calibration unit also M6 × 8 mm
- E3D V6 and clone hotend nozzles also M6 × 6 mm
- Large drones (Matrice-class payloads) also M6 × 10 mm
- Rack ears on pro-audio gear also M6 × 8–10 mm
Questions about Dashcam suction mount ball joint (large) screws
- What size screw does Dashcam suction mount ball joint (large) use?
- M6 × 6–10 mm for CH01B universal tripod ball mount offered with M4 or M6 screw joint.
- How long are the screws in Dashcam suction mount ball joint (large)?
- The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Dashcam suction mount ball joint (large)?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.