How long are the screws in Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw?

The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw?

TechSpareWarehouse (our own store) lists M3 x 4mm, M3 x 5mm and M3 x 6mm, which match lengths in the records above.

Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw screw size

M3 · 4 to 6 mm long

The screws used on Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw are M3 in lengths from 4 to 6 mm.

It is listed for parts listing: 'Diebold Nixdorf ESC Cross Screw M3*4*6 ATM Parts 49221808000F' — screw described explicitly as M3.

This entry is marked confirmed and comes from atm-machineparts.com.

M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	4–6 mm	0.5 mm	not stated	not stated	Parts listing: 'Diebold Nixdorf ESC Cross Screw M346 ATM Parts 49221808000F' — screw described explicitly as M3	Confirmed

Fitment records and sources

M3M3x4x6 mm (head dia x length variant)confirmed — Diebold Nixdorf OEM parts listing

Parts listing: 'Diebold Nixdorf ESC Cross Screw M3*4*6 ATM Parts 49221808000F' — screw described explicitly as M3

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Consoles and controllers often use security drives (tri-wing, Torx) and short screws into plastic bosses, so do not over-tighten.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 4–6 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

GoPro's own official Dive Housing user guide does not itself state a metric screw size for the housing body; only third-party accessory manufacturer (INON) manuals explicitly cite M6 screws for their add-on arms/adapters attaching to the housing.
Suunto dive computer service manuals reference strap pins and battery compartment springs but do not explicitly cite a metric screw thread size in the sections reviewed; do not infer M2/M2.5 fitment for Suunto dive computer straps without direct confirmation.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Gaming & Peripherals

Arcade cabinet control panel Dell Latitude 3190 / 3190 2-in-1 Dell Latitude 3490 Dell XPS 13 9315 Docking station internal boards Feurich Olya EVO digital piano/E-Piano Generic tray-mount mechanical keyboards HTC Vive controller Inkjet printer / scanner frames KBDfans countersunk standoff kit Keychron K3 / K3 Pro / K3 Max Keychron K4 Pro and Q1 keyboards

Browse all 30 in Gaming & Peripherals →

The same screw also fits

Devices whose records share a thread with Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw, closest length match first.

Keychron Q1 mechanical keyboard also M3 × 6 mm
USB-C docking station chassis also M3 × 6 mm
Keychron K4 Pro and Q1 keyboards also M3 × 6 mm
Dell Latitude D520 also M3 × 5 mm
PW-Sat2 CubeSat structural frame also M3 × 5–6 mm
DIN 7500 rolled-thread machine screw sold as aviation/aircraft hardware also M3 × 6 mm
Dell Latitude 7424 also M3 × 6 mm
Acer TravelMate 5520G also M3 × 4 mm

Questions about Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw screws

What size screw does Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw use?: M3 × 4–6 mm for parts listing: 'Diebold Nixdorf ESC Cross Screw M3*4*6 ATM Parts 49221808000F' — screw described explicitly as M3.
How long are the screws in Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw?: The records range from 4 to 6 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw?: TechSpareWarehouse (our own store) lists M3 x 4mm, M3 x 5mm and M3 x 6mm, which match lengths in the records above.

Heads up: shipping delay