KBDfans countersunk standoff kit screw size
M2 · length not stated in the sources
Our records put KBDfans countersunk standoff kit on M2 screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for countersunk flat-head standoff screw compatible with multiple KBDfans keyboard cases.
Head and drive, as the source states them: flat / countersunk head.
This entry is marked confirmed and comes from divinikey.com.
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
KBDfans countersunk standoff kit screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | not stated | 0.4 mm | Flat / countersunk | not stated | Countersunk flat-head standoff screw compatible with multiple KBDfans keyboard cases | Confirmed |
Fitment records and sources
Countersunk flat-head standoff screw compatible with multiple KBDfans keyboard cases
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Keep long and short screws apart when opening a console; the shell positions differ.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- M.2 SSD screw length must match the standoff position (2230/2242/2260/2280/22110) or the drive won't clamp.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
More in Gaming & Peripherals
The same screw also fits
Devices whose records share a thread with KBDfans countersunk standoff kit, closest length match first.
- HTC Vive controller also M2
- Keychron K3 / K3 Pro / K3 Max also M2
- Valve Index controller (Knuckles) also M2
- Meta Quest 2 controller also M2
- M.2 NVMe SSD retention screw also M2
- Xbox One wireless controller also M2
- Xbox Elite Series 2 controller also M2
- Valve Index headset face gasket mount also M2
Questions about KBDfans countersunk standoff kit screws
- What size screw does KBDfans countersunk standoff kit use?
- M2 for countersunk flat-head standoff screw compatible with multiple KBDfans keyboard cases.
- How long are the screws in KBDfans countersunk standoff kit?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for KBDfans countersunk standoff kit?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.