Dell XPS 13 9315 screw size
M1.6 · 1.5 to 2 mm long
If you are replacing a screw on Dell XPS 13 9315, the thread is M1.6 in lengths from 1.5 to 2 mm.
The record covers palmrest / keyboard assembly retention screws.
This entry is marked reported and comes from parts-people.com.
M1.6 means a 1.6 mm nominal diameter with a 0.35 mm thread pitch. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent.
Dell XPS 13 9315 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.6 | 1.5–2 mm | 0.35 mm | not stated | not stated | palmrest / keyboard assembly retention screws | Reported |
Fitment records and sources
palmrest / keyboard assembly retention screws
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
How to check the screw before you buy
- Consoles and controllers often use security drives (tri-wing, Torx) and short screws into plastic bosses, so do not over-tighten.
- Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 1.5–2 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M1.6 heads take PH00 for Phillips and T4–T5 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.6
- M1.6 is the most common laptop-internal micro screw after M2 — Dell XPS keyboards specifically call out M1.6 x 1.5mm, and generic M2 substitutes strip the bracket.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Gaming & Peripherals
The same screw also fits
Devices whose records share a thread with Dell XPS 13 9315, closest length match first.
- Lenovo ThinkPad P14s Gen 3 also M1.6 × 1.8 mm
- Lenovo ideapad 320SX-14IKB also M1.6 × 2 mm
- Dell XPS 13 9310 also M1.6 × 2 mm
- HP ENVY 17-cg1000 (ids 32552529 also M1.6 × 2 mm
- Dell 16 Premium DA16250 also M1.6 × 2 mm
- HP OMEN 17.3 inch Gaming 17-ck0000 also M1.6 × 2 mm
- HP mt46 Mobile Thin Client (id 37874521; MSG on PAGE 2) also M1.6 × 1.8 mm
- Framework Laptop 16 (AMD Ryzen AI 300) also M1.6 × 1.5 mm
Questions about Dell XPS 13 9315 screws
- What size screw does Dell XPS 13 9315 use?
- M1.6 × 1.5–2 mm for palmrest / keyboard assembly retention screws.
- How long are the screws in Dell XPS 13 9315?
- The records range from 1.5 to 2 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M1.6 screw?
- 0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.
- What screwdriver do I need for Dell XPS 13 9315?
- The sources do not name the drive. For M1.6, Phillips heads normally take PH00 and Torx heads T4–T5; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M1.6?
- No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.