Drum hardware wing bolt / memory lock screw size
M4 · 10 to 20 mm long
The screws used on Drum hardware wing bolt / memory lock are M4 in lengths from 10 to 20 mm.
Where it is used: cymbal stand and hardware joints.
This entry is marked reported and comes from alibaba.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Drum hardware wing bolt / memory lock screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10–20 mm | 0.7 mm | not stated | not stated | cymbal stand and hardware joints | Reported |
Fitment records and sources
cymbal stand and hardware joints
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Instrument and audio hardware often threads into wood or thin metal; a screw that is too long can poke through a finished surface.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Grounding-lug screws on Siemens and Beckhoff gear (M4) are earth hardware, not structural mounting screws — don't reuse them to hold a module.
- Not all telescope/finder hardware is metric — Celestron Edge/NexStar SE finder-shoe and dovetail screws are reported as 8/32 (imperial UNC), so metric M4/M5 fitments cannot be assumed across all Celestron products; must check per accessory/vintage.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size -
M4 x 16mm Black Wafer Head Assembly Screws for xTool D1 Pro Laser Engraver – 10-Pack Replacement
$5.99Choose size -
M4 x 16mm Black Wafer Head Monitor VESA & Stand Screws for Sceptre E415B, C345B-QUN168W, C305B-FUN200W1, E345B-QU180D & U550CV – 8-Pack Replacement
$5.99Choose size
More in Audio, Music & Stage
Accordion reed blocksAllparts metric bridge length screwsARRI Mini Follow Focus MFF-2 / related follow-focus hardwareBoss compact guitar pedal battery doorCymbal stand / hi-hat wing nutCymbal stand top wing nutCymbal stand wing nutDrum tension rodDrum tension rod / lug mounting screwDuratruss Mini 360 F14 10kg truss clampFender Standard Series bass bridgeFender/Squier import Stratocaster & Jazzmaster bridge
Browse all 48 in Audio, Music & Stage →The same screw also fits
Devices whose records share a thread with Drum hardware wing bolt / memory lock, closest length match first.
- Martin MAC 500 moving head fixture also M4 × 10–20 mm
- Speaker driver to baffle also M4 × 12–20 mm
- Bezzera Giulia espresso machine also M4 × 13 mm
- ETC Unison DRd Rack Enclosure (dimming rack for theatrical rigging systems) also M4 × 10 mm
- Circular saw blade guard pivot also M4 × 12–18 mm
- Metcase Technomet-Control instrument enclosure also M4 × 16 mm
- ASUS VG32AQA1A also M4 × 10 mm
- Dell Pro P 24 16:10 monitor (P2426E) also M4 × 10 mm
Questions about Drum hardware wing bolt / memory lock screws
- What size screw does Drum hardware wing bolt / memory lock use?
- M4 × 10–20 mm for cymbal stand and hardware joints.
- How long are the screws in Drum hardware wing bolt / memory lock?
- The records range from 10 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Drum hardware wing bolt / memory lock?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.