How long are the screws in Duratruss Mini 360 F14 10kg truss clamp?

The record gives 16 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M6 screw?

1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.

What screwdriver do I need for Duratruss Mini 360 F14 10kg truss clamp?

The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.

Can I use an imperial screw instead of M6?

No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.

Duratruss Mini 360 F14 10kg truss clamp screw size

M6 · 16 mm long

If you are replacing a screw on Duratruss Mini 360 F14 10kg truss clamp, the thread is M6, 16 mm long.

It is listed for device screw: M6, 16mm long, for 18-20mm diameter truss tubes.

Head and drive, as the source states them: truss head.

This entry is marked confirmed and comes from thomann.ie.

For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.

Duratruss Mini 360 F14 10kg truss clamp screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M6	16 mm	1 mm	Truss head	not stated	Device screw: M6, 16mm long, for 18-20mm diameter truss tubes	Confirmed

Fitment records and sources

M616confirmed

Device screw: M6, 16mm long, for 18-20mm diameter truss tubes

pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30

Source

How to check the screw before you buy

Instrument and audio hardware often threads into wood or thin metal; a screw that is too long can poke through a finished surface.
Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: for truss head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
The record states 16 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.

Common mix-ups with M6

Burton sells two different M6 lengths: M6x16 for Re:Flex on 4x4/3D boards and M6x13 for EST on Channel boards. The 16mm screw can bottom out or dimple a Channel board base.
Rack cage-nut screws for audio gear are usually M6, but the same rack may also take 10-32 or 12-24 imperial screws.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Audio, Music & Stage

Accordion reed blocks Allparts metric bridge length screws ARRI Mini Follow Focus MFF-2 / related follow-focus hardware Boss compact guitar pedal battery door Cymbal stand / hi-hat wing nut Cymbal stand top wing nut Cymbal stand wing nut Drum hardware wing bolt / memory lock Drum tension rod Drum tension rod / lug mounting screw Fender Standard Series bass bridge Fender/Squier import Stratocaster & Jazzmaster bridge

Browse all 48 in Audio, Music & Stage →

The same screw also fits

Devices whose records share a thread with Duratruss Mini 360 F14 10kg truss clamp, closest length match first.

QSC K12 loudspeaker yoke mount also M6 × 16 mm
Orthotic joint hinge bolt also M6 × 16 mm
DIN 912 socket-head cap screw also M6 × 16 mm
Xiaomi M365 / Ninebot brake caliper also M6 × 16 mm
DIN 965 / ISO 7046 countersunk Phillips screw also M6 × 16 mm
Thule Bike Racks (General Replacement) also M6 × 16 mm
TV wall mount, VESA 200x200 and larger also M6 × 16 mm
TCL & Vizio 43-55in TVs also M6 × 16 mm

Questions about Duratruss Mini 360 F14 10kg truss clamp screws

What size screw does Duratruss Mini 360 F14 10kg truss clamp use?: M6 × 16 mm for device screw: M6, 16mm long, for 18-20mm diameter truss tubes.
How long are the screws in Duratruss Mini 360 F14 10kg truss clamp?: The record gives 16 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M6 screw?: 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
What screwdriver do I need for Duratruss Mini 360 F14 10kg truss clamp?: The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
Can I use an imperial screw instead of M6?: No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.

Heads up: shipping delay