Framework Laptop 13 fingerprint bracket / expansion card screw screw size
M1.4 · 3.5 mm long
Our records put Framework Laptop 13 fingerprint bracket / expansion card screw on M1.4 screws, 3.5 mm long.
It is listed for T5 head, 3.0mm head dia.
Head and drive, as the source states them: Torx T5 drive.
This entry is marked confirmed and comes from guides.frame.work.
For reference, M1.4 is 1.4 mm across the threads at 0.3 mm pitch. The imperial size people confuse it with: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Framework Laptop 13 fingerprint bracket / expansion card screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 3.5 mm | 0.3 mm | not stated | Torx T5 | T5 head, 3.0mm head dia | Confirmed |
Fitment records and sources
T5 head, 3.0mm head dia
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 3.5 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Torx T5 drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Laptops & PCs
The same screw also fits
Devices whose records share a thread with Framework Laptop 13 fingerprint bracket / expansion card screw, closest length match first.
- Framework Laptop 13 fingerprint reader bracket / expansion card bracket also M1.4 × 3.5 mm
- Framework Laptop 13 fingerprint reader bracket also M1.4 × 3.5 mm
- Dell Pro Max 16 Premium MA16250 also M1.4 × 3.5 mm
- Oakley O Matter / steel frame hinge also M1.4 × 3.5 mm
- Spectacle frame hinge screws (ISO 11381 standard) also M1.4 × 3.5 mm
- NBK SPE-MC PEEK micro pan head screws also M1.4 × 3.5 mm
- Eyeglass & sunglass metal hinges also M1.4 × 3.5 mm
- Sennheiser MOMENTUM M2 On-Ear headphone also M1.4 × 3.5 mm
Questions about Framework Laptop 13 fingerprint bracket / expansion card screw screws
- What size screw does Framework Laptop 13 fingerprint bracket / expansion card screw use?
- M1.4 × 3.5 mm for T5 head, 3.0mm head dia.
- How long are the screws in Framework Laptop 13 fingerprint bracket / expansion card screw?
- The record gives 3.5 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Framework Laptop 13 fingerprint bracket / expansion card screw?
- The source lists a Torx T5 drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.