GE HealthCare Anesthesia Delivery Systems screw size
M6 · 25 mm long
GE HealthCare Anesthesia Delivery Systems takes M6 metric screws, 25 mm long.
Where it is used: countersunk Socket Head Stainless Steel Screw (Item No. 1009-3352-000).
Head and drive, as the source states them: flat / countersunk head.
This entry is marked confirmed and comes from services.gehealthcare.com.
For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
GE HealthCare Anesthesia Delivery Systems screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 25 mm | 1 mm | Flat / countersunk | not stated | Countersunk Socket Head Stainless Steel Screw (Item No. 1009-3352-000)stainless | Confirmed |
Fitment records and sources
Countersunk Socket Head Stainless Steel Screw (Item No. 1009-3352-000)
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Keep material and finish the same as the original (often stainless) on equipment that is cleaned or sterilised.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
- The record states 25 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- TS-Optics Losmandy-style dovetail bars drill through-holes sized to accept either M6 metric screws or 1/4" imperial screws interchangeably in the same countersunk holes.
More in Medical & Laboratory
Agilent 1100 LC/MSD mass spectrometerAgilent 8453 UV-Visible spectrophotometerAlaris 8110/8120 infusion pumpBehind-the-ear hearing aid shellBelmont Eurus S6 Dental UnitBHI Implants Rosen screwBicycle SPD-SL / SPD cleat fixing boltsBien-Air Dental HandpiecesBioHorizons CONELOG Dental ImplantsBlind-tapped DN16CF ConFlat vacuum flange (metric)BMC RESmart CPAP machineBredent dental prosthetic screw
Browse all 92 in Medical & Laboratory →The same screw also fits
Devices whose records share a thread with GE HealthCare Anesthesia Delivery Systems, closest length match first.
- Mocom Dental Autoclaves also M6 × 25 mm
- Orthotic joint hinge bolt also M6 × 25 mm
- ISO 7380 button head socket screw also M6 × 25 mm
- Newport M-ST-UT2-410-8 SmartTable also M6 × 25 mm
- Premier Mounts PBL-UMS/PBL-UMW Universal Projector Mount also M6 × 25 mm
- Furniture leveling foot also M6 × 25 mm
- Optical breadboard / optical table (metric) also M6 × 25 mm
- Appliance door hinges also M6 × 25 mm
Questions about GE HealthCare Anesthesia Delivery Systems screws
- What size screw does GE HealthCare Anesthesia Delivery Systems use?
- M6 × 25 mm for countersunk Socket Head Stainless Steel Screw (Item No. 1009-3352-000).
- How long are the screws in GE HealthCare Anesthesia Delivery Systems?
- The record gives 25 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for GE HealthCare Anesthesia Delivery Systems?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.