Mocom Dental Autoclaves screw size
M6 · 25 mm long
Our records put Mocom Dental Autoclaves on M6 screws, 25 mm long.
Where it is used: stainless steel hex socket head screw (SKU: Mocom18-51232135).
Head and drive, as the source states them: Hex socket (Allen) drive.
This entry is marked confirmed and comes from elexadent.com.
For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Mocom Dental Autoclaves screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 25 mm | 1 mm | not stated | Hex socket (Allen) | Stainless steel hex socket head screw (SKU: Mocom18-51232135)stainless | Confirmed |
Fitment records and sources
Stainless steel hex socket head screw (SKU: Mocom18-51232135)
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Keep material and finish the same as the original (often stainless) on equipment that is cleaned or sterilised.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 25 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Hex socket (Allen) drive. For comparison, standard M6 heads take PH3 (Phillips) or T30 (Torx), or a 5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
More in Medical & Laboratory
The same screw also fits
Devices whose records share a thread with Mocom Dental Autoclaves, closest length match first.
- GE HealthCare Anesthesia Delivery Systems also M6 × 25 mm
- Orthotic joint hinge bolt also M6 × 25 mm
- ISO 7380 button head socket screw also M6 × 25 mm
- Furniture leveling foot also M6 × 25 mm
- Newport M-ST-UT2-410-8 SmartTable also M6 × 25 mm
- Premier Mounts PBL-UMS/PBL-UMW Universal Projector Mount also M6 × 25 mm
- Appliance door hinges also M6 × 25 mm
- Pride Go-Go scooter tiller lock knob also M6 × 25 mm
Questions about Mocom Dental Autoclaves screws
- What size screw does Mocom Dental Autoclaves use?
- M6 × 25 mm for stainless steel hex socket head screw (SKU: Mocom18-51232135).
- How long are the screws in Mocom Dental Autoclaves?
- The record gives 25 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Mocom Dental Autoclaves?
- The source lists a Hex socket (Allen) drive. Standard M6 heads otherwise take PH3 (Phillips) or T30 (Torx), or a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.