ISO 7380 button head socket screw screw size
M6 · 6 to 25 mm long
If you are replacing a screw on ISO 7380 button head socket screw, the thread is M6 in lengths from 6 to 25 mm.
Where it is used: available M3-M10 where a low rounded head is needed.
This entry is marked confirmed and comes from aluxprofile.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
ISO 7380 button head socket screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 6–25 mm | 1 mm | not stated | not stated | Available M3-M10 where a low rounded head is needed | Confirmed |
Fitment records and sources
Available M3-M10 where a low rounded head is needed
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- For medical and lab equipment, use the manufacturer's replacement part where one is specified; the thread size here helps identify it, not certify it.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–25 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Medical & Laboratory
The same screw also fits
Devices whose records share a thread with ISO 7380 button head socket screw, closest length match first.
- SISAB ECO.50+/T laboratory centrifuge also M6 × 20 mm
- Philips 15210B calibration unit also M6 × 8 mm
- IV pole clamps also M6 × 10–20 mm
- Orthotic joint hinge bolt also M6 × 12–25 mm
- GE HealthCare Anesthesia Delivery Systems also M6 × 25 mm
- Mocom Dental Autoclaves also M6 × 25 mm
- TSC MH241 industrial label printer also M6 × 12 mm
- Ottobock 17AD1 ankle joint screw (M6) also M6 × 6 mm
Questions about ISO 7380 button head socket screw screws
- What size screw does ISO 7380 button head socket screw use?
- M6 × 6–25 mm for available M3-M10 where a low rounded head is needed.
- How long are the screws in ISO 7380 button head socket screw?
- The records range from 6 to 25 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for ISO 7380 button head socket screw?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.