Genmitsu 3018-PROVer CNC router screw size
M3 · length not stated in the sources
The screws used on Genmitsu 3018-PROVer CNC router are M3. None of the sources we found gives an exact length, so measure the original before you order.
The record covers assembly manual documents M3 hardware for control-box and board mounting.
This entry is marked reported and comes from m.media-amazon.com.
M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Genmitsu 3018-PROVer CNC router screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | Assembly manual documents M3 hardware for control-box and board mounting | Reported |
Fitment records and sources
Assembly manual documents M3 hardware for control-box and board mounting
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Printer and CNC builds usually publish a bill of materials; when it lists a length, follow it, since extrusion T-nuts and motor faces have fixed thread depths.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Pond/aquarium equipment manuals aimed at consumers rarely specify exact thread pitch or length for internal fasteners, since these are considered non-user-serviceable; distributor-level assembly/service manuals (e.g., Maytronics internal documents) are a better source than end-user guides.
- Thor Zone Nanoq S case mixes metric M3 (various lengths: 4, 5, 6, 10, 13, 20mm) and imperial #6-32 UNC fasteners across the same build, so builders must sort hardware carefully rather than assuming an all-metric kit.
More in 3D Printing, CNC & Robotics
2020 extrusion T-nuts (light duty)2020 extrusion T-nuts (standard)2020 T-slot hammer head bolts2020/2040 extrusion end tap2040 extrusion T-nuts3030 extrusion T-nuts (heavy duty)3030/4040 extrusion end tap3D printer & CNC enclosures3D printer hotend to X-carriageActobotics servo horn / hubArduino Mega 2560 mounting holesArduino shield stacking standoffs
Browse all 149 in 3D Printing, CNC & Robotics →The same screw also fits
Devices whose records share a thread with Genmitsu 3018-PROVer CNC router, closest length match first.
- REV Robotics hex standoffs also M3
- Bambu Lab X1/P1 General machine screws throughout the printer also M3
- Carbide3D proximity switch upgrade kit also M3
- ESP32 DevKit boards also M3
- Prusa MK4 / MK4S kit also M3
- Ender 3 V2 hotend and hotend cover also M3
- Arduino Mega 2560 mounting holes also M3
- Prusa MK3S/MK3.5 to MK4 upgrade kit also M3
Questions about Genmitsu 3018-PROVer CNC router screws
- What size screw does Genmitsu 3018-PROVer CNC router use?
- M3 for assembly manual documents M3 hardware for control-box and board mounting.
- How long are the screws in Genmitsu 3018-PROVer CNC router?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Genmitsu 3018-PROVer CNC router?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.