Google Pixel 6 screw size
M1.2 · 4.2 mm long
The screws used on Google Pixel 6 are M1.2, 4.2 mm long.
Where it is used: official Google Pixel 6 screw, part G250-05801-00, listed by vendor as "M1.2,4.2" (thread size M1.2, length 4.2mm per Google part code convention).
This entry is marked confirmed and comes from nutelsolutions.co.uk.
An M1.2 screw is 1.2 mm in diameter with a 0.25 mm pitch, tapped with a 0.95 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute.
Google Pixel 6 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.2 | 4.2 mm | 0.25 mm | not stated | not stated | Official Google Pixel 6 screw, part G250-05801-00, listed by vendor as "M1.2,4.2" (thread size M1.2, length 4.2mm per Google part code convention) | Confirmed |
Fitment records and sources
Official Google Pixel 6 screw, part G250-05801-00, listed by vendor as "M1.2,4.2" (thread size M1.2, length 4.2mm per Google part code convention)
pitch 0.25 mm · tap 0.95 mm · clearance 1.4 mm · PH000 / JIS 00 / Torx T1–T2
How to check the screw before you buy
- Take one original screw out first and measure it before ordering; the record above tells you the thread, the original screw tells you the exact length and head.
- Diameter: across the threads an M1.2 screw measures about 1.2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.25 mm from one thread crest to the next (40 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 4.2 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M1.2 heads take PH000 / JIS 00 for Phillips and T1–T2 for Torx; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.2 is about 5-8 N·cm into metal threads and 3-5 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.2
- M1.2 and M1.4 look identical in an eyeglass repair kit — the wrong one strips soft acetate or metal hinges.
More in Other Equipment
The same screw also fits
Devices whose records share a thread with Google Pixel 6, closest length match first.
- Laptop/keyboard/phone repair micro screws also M1.2 × 4.2 mm
- Micro FPV / tiny-whoop drones also M1.2 × 4.2 mm
- NBK SPE-MC PEEK micro pan head screws also M1.2 × 4.2 mm
- Arduino / small PCB stacks also M1.2 × 4.2 mm
- NBK SSCZS pan-head captive miniature screw for precision instruments also M1.2 × 4.2 mm
- Micro servos (hobby RC) also M1.2 × 4.2 mm
- Scale models & RC detail parts also M1.2 × 4.2 mm
- Google Pixel 5 also M1.2
Questions about Google Pixel 6 screws
- What size screw does Google Pixel 6 use?
- M1.2 × 4.2 mm for official Google Pixel 6 screw, part G250-05801-00, listed by vendor as "M1.2,4.2" (thread size M1.2, length 4.2mm per Google part code convention).
- How long are the screws in Google Pixel 6?
- The record gives 4.2 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.2 screw?
- 0.25 mm (coarse), which is the standard pitch for M1.2 machine screws. The tap drill is 0.95 mm and the normal clearance hole is 1.4 mm.
- What screwdriver do I need for Google Pixel 6?
- The sources do not name the drive. For M1.2, Phillips heads normally take PH000 / JIS 00 and Torx heads T1–T2.
- Can I use an imperial screw instead of M1.2?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute. Use a true M1.2 screw so it does not cross-thread or strip the hole.