GP-SR1-PC200 LiFePO4 battery DIY kit screw size
M6 · length not stated in the sources
GP-SR1-PC200 LiFePO4 battery DIY kit takes M6 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers torque table specifies M6 busbar/module hardware at 8 N-m.
This entry is marked confirmed and comes from gobelpower.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
GP-SR1-PC200 LiFePO4 battery DIY kit screw specifications
One row per fitment record. Head, drive and torque are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Torque | Where it goes | Status |
|---|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | 8 N-m | Torque table specifies M6 busbar/module hardware at 8 N-m | Confirmed |
Fitment records and sources
Torque table specifies M6 busbar/module hardware at 8 N-m
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- If several screws hold the same part, check that they are all the same length before assuming they are.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Common mix-ups with M6
- No screw length given, only torque — measure existing hardware before replacing.
- Astro dovetail hardware is inconsistent: Losmandy-brand dovetail plate screws are 1/4-20 (imperial) per Losmandy/Astro-Physics documentation, while PrimaLuceLab's PLUS-standard dovetails explicitly use M6 — don't assume metric across all 'Losmandy-style' dovetail ecosystems.
More in Standards & References
2.5in SATA SSD / HDDABB REX640 protection & control relayAgilent (HP) 8453 UV-Visible Spectroscopy SystemAirsoft AEG Version 2 / EHPA gearbox shellARRI rosette accessory adapterBalisong / butterfly knife pivot (aftermarket, ISO 14583 pan head)Beckhoff AMP8x3x distributed servo drive flange mountingBeckhoff AMP8x4x distributed servo drive flange mountingCanadian Solar standard PV modulesCubeSat Kit solar panel clips and chassisDIN 912 socket-head cap screwDIN 912 socket-head cap screw (smallest size)
Browse all 31 in Standards & References →The same screw also fits
Devices whose records share a thread with GP-SR1-PC200 LiFePO4 battery DIY kit, closest length match first.
- ISO-KF vacuum flange claw clamps (DN10-DN50) also M6
- Beckhoff AMP8x4x distributed servo drive flange mounting also M6
- Speck 95-IX / 95-X commercial pool pump also M6
- HDRiG ARRI-standard rosette (31.8mm) also M6
- DIN 965 / ISO 7046 countersunk Phillips screw also M6
- DIN 912 socket-head cap screw also M6
- ICE arcade games also M6
- Lekkie 5mm motor spacer for Bafang BBSHD/BBS02 also M6
Questions about GP-SR1-PC200 LiFePO4 battery DIY kit screws
- What size screw does GP-SR1-PC200 LiFePO4 battery DIY kit use?
- M6 for torque table specifies M6 busbar/module hardware at 8 N-m.
- How long are the screws in GP-SR1-PC200 LiFePO4 battery DIY kit?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for GP-SR1-PC200 LiFePO4 battery DIY kit?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.
- How tight should the M6 screw on GP-SR1-PC200 LiFePO4 battery DIY kit be?
- The source gives 8 N-m for torque table specifies M6 busbar/module hardware at 8 N-m.