Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas screw size
M1.6 · 10 mm long
Our records put Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas on M1.6 screws, 10 mm long.
Where it is used: reed-plate and cover-plate screws.
This entry is marked confirmed and comes from wilsonmusic.ca.
M1.6 means a 1.6 mm nominal diameter with a 0.35 mm thread pitch. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent.
Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.6 | 10 mm | 0.35 mm | not stated | not stated | reed-plate and cover-plate screws | Confirmed |
Fitment records and sources
reed-plate and cover-plate screws
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
How to check the screw before you buy
- Stage and rack gear mixes metric with #10-32 rack screws, so check before swapping.
- Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M1.6 heads take PH00 for Phillips and T4–T5 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Audio, Music & Stage
The same screw also fits
Devices whose records share a thread with Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas, closest length match first.
- NBK SSCZS miniature captive screw for precision instruments also M1.6 × 10 mm
- DIN 965 / ISO 7046 countersunk Phillips screw also M1.6 × 10 mm
- DIN 912 socket-head cap screw also M1.6 × 10 mm
- Precision instrument hex socket head screws (used in cameras/electronics repair) also M1.6 × 10 mm
- Lenovo ideapad 520S-14IKB also M1.6
- Dell Latitude 5424 also M1.6
- Dell G7 15 7588 also M1.6
- HP EliteBook x360 830 G8 also M1.6
Questions about Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas screws
- What size screw does Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas use?
- M1.6 × 10 mm for reed-plate and cover-plate screws.
- How long are the screws in Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.6 screw?
- 0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.
- What screwdriver do I need for Hohner Crossover / Golden Melody / Rocket / Special 20, MS series, Seydel harmonicas?
- The sources do not name the drive. For M1.6, Phillips heads normally take PH00 and Torx heads T4–T5; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M1.6?
- No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.