HP P22 G5 screw size
M2 / M3 / M4 · 3 to 10 mm long
Our records put HP P22 G5 on M2, M3 and M4 screws in lengths from 3 to 10 mm.
There are 11 separate fitment records for it, including stand (qty 1, silver) (M2), vesa mount (qty 1, silver) (M2) and unspecified (silver) (M2), plus 8 more in the table below.
11 of the 11 records are marked confirmed, drawn from 1 source (h10032.www1.hp.com).
An M2 screw is 2 mm in diameter with a 0.4 mm pitch, tapped with a 1.6 mm drill; imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
HP P22 G5 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 3 mm | 0.4 mm | not stated | not stated | Stand (qty 1, silver) | Confirmed |
| M2 | 3 mm | 0.4 mm | not stated | not stated | Vesa mount (qty 1, silver) | Confirmed |
| M2 | 4 mm | 0.4 mm | not stated | not stated | Unspecified (silver) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Back cover (black)black finish | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Stand (silver) | Confirmed |
| M3 | 4 mm | 0.5 mm | not stated | not stated | Vesa mount (black)black finish | Confirmed |
| M3 | 5 mm | 0.5 mm | not stated | not stated | Vesa mount (silver) | Confirmed |
| M3 | 6 mm | 0.5 mm | not stated | not stated | Stand (black)black finish | Confirmed |
| M3 | 8 mm | 0.5 mm | not stated | not stated | Vesa mount (black)black finish | Confirmed |
| M4 | 10 mm | 0.7 mm | not stated | not stated | Back cover (black)black finish | Confirmed |
| M4 | 10 mm | 0.7 mm | not stated | not stated | Vesa mount (black)black finish | Confirmed |
Fitment records and sources
Stand (qty 1, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Vesa mount (qty 1, silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Unspecified (silver)
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
Back cover (black)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Stand (silver)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Vesa mount (black)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Vesa mount (silver)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Stand (black)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Vesa mount (black)
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Back cover (black)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Vesa mount (black)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M3 / M4, so measure each screw rather than assuming they match.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2 / M3 / M4
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
- Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
- VESA fixes the hole pattern and max thread depth, not screw length — length depends on the panel back and any spacers.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 3mm Screws for Dell XPS 13 9340 Base Cover SSD Shield 10-Pack Black
$4.99 -
10x M2 x 3mm Phillips Screws for Lenovo ThinkPad X131e Chromebook WiFi SSD
$4.99
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M3 x 4mm Phillips Wafer Head Screws for 2.5 SATA SSD Mounting 10-Pack
$4.99 -
M3 x 4mm Screws for Installing SSD into Synology NAS 10-Pack
$4.99 -
M3 x 4mm Phillips Wafer Head Screws for HDD Caddy Bracket 10-Pack
$4.99 -
M3 x 4mm Phillips Wafer Head Screws for SSD Hard Drive 10-Pack Black
$4.99
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with HP P22 G5, closest length match first.
- TSC MB241/MB341 industrial barcode printer also M3 × 4 mm
- Dell Pro 14 Plus portable monitor (P1425) also M2 × 3 mm
- Dell S2421HGF also M3 × 6 mm
- Dell S2417DG also M3 × 6 mm
- QualGear QG-KIT-VA-3IN-B Projector Mounting Kit also M3 × 8 mm
- Dell P1913S also M3 × 6 mm
- ASUS VP229HF also M4 × 10 mm
- Raspberry Pi VESA adapter plates also M4 × 10 mm
Questions about HP P22 G5 screws
- What size screw does HP P22 G5 use?
- M2 × 3 mm for stand (qty 1, silver); M2 × 3 mm for vesa mount (qty 1, silver); M2 × 4 mm for unspecified (silver); M3 × 4 mm for back cover (black); M3 × 4 mm for stand (silver); M3 × 4 mm for vesa mount (black); M3 × 5 mm for vesa mount (silver); M3 × 6 mm for stand (black); M3 × 8 mm for vesa mount (black); M4 × 10 mm for back cover (black); M4 × 10 mm for vesa mount (black).
- How long are the screws in HP P22 G5?
- The records range from 3 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for HP P22 G5?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for HP P22 G5?
- TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M3 x 4mm, which match lengths in the records above.