Husqvarna 327RDX brushcutter housing screw size
M6 · 20 mm long
Husqvarna 327RDX brushcutter housing takes M6 metric screws, 20 mm long.
Where it is used: OEM Husqvarna 725237071 hex screw M6S 6x20.
This entry is marked confirmed and comes from ereplacementparts.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Husqvarna 327RDX brushcutter housing screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 20 mm | 1 mm | not stated | not stated | OEM Husqvarna 725237071 hex screw M6S 6x20 | Confirmed |
Fitment records and sources
OEM Husqvarna 725237071 hex screw M6S 6x20
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Check the strength class stamped on the head (8.8, 10.9, A2-70) and replace like for like.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 20 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
More in Industrial & Machinery
ABB ACS580 motor terminal box / cable glandsABB ACS580 terminal hardware (frames R3-R5)ABB random-wound motor terminal boxes (ACS580 drive systems)Allen-Bradley ControlLogix 1756-A chassisAngle grinder gear housingBianchi / Nuova Simonelli / Rheavendors / Saeco vending machineCircular saw blade guard pivotContender Planetary Mixer MXP004/MXP005 (commercial bakery mixer) electrical diagram terminal screwsCordless drill housing shellsCOSEL power supply terminal block (used in industrial/pump/water-treatment control panels)Datalogic DS2400 fixed-mount barcode readerDeWalt D51430 / D51431 pneumatic nailer
Browse all 113 in Industrial & Machinery →The same screw also fits
Devices whose records share a thread with Husqvarna 327RDX brushcutter housing, closest length match first.
- Makita JR3051TK reciprocating saw also M6 × 20 mm
- ICE arcade games also M6 × 20 mm
- DIN 965 / ISO 7046 countersunk Phillips screw also M6 × 20 mm
- Xiaomi M365 / Ninebot brake caliper also M6 × 20 mm
- TV wall mount, VESA 200x200 and larger also M6 × 20 mm
- Orthotic joint hinge bolt also M6 × 20 mm
- Gas grill cart and legs also M6 × 20 mm
- DIN 912 socket-head cap screw also M6 × 20 mm
Questions about Husqvarna 327RDX brushcutter housing screws
- What size screw does Husqvarna 327RDX brushcutter housing use?
- M6 × 20 mm for OEM Husqvarna 725237071 hex screw M6S 6x20.
- How long are the screws in Husqvarna 327RDX brushcutter housing?
- The record gives 20 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Husqvarna 327RDX brushcutter housing?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.