Milwaukee tool torque specification sheet (PN0007936) screw size
M2 · 0.89 mm long
Milwaukee tool torque specification sheet (PN0007936) takes M2 metric screws, 0.89 mm long.
The record covers named fastener "Screw M2 x 0.89 PH Torx T6" with a specified seating torque.
Head and drive, as the source states them: Torx T6 drive.
This entry is marked confirmed and comes from documents.milwaukeetool.com.
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Milwaukee tool torque specification sheet (PN0007936) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 0.89 mm | 0.4 mm | not stated | Torx T6 | Named fastener "Screw M2 x 0.89 PH Torx T6" with a specified seating torque | Confirmed |
Fitment records and sources
Named fastener "Screw M2 x 0.89 PH Torx T6" with a specified seating torque
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Check the strength class stamped on the head (8.8, 10.9, A2-70) and replace like for like.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 0.89 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Torx T6 drive. For comparison, standard M2 heads take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- Framework 13 and 16 use five thread families (M1.2 to M2.5) with overlapping lengths; buy Framework's own fastener kit rather than generic M2 screws.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
More in Industrial & Machinery
ABB ACS580 motor terminal box / cable glandsABB ACS580 terminal hardware (frames R3-R5)ABB random-wound motor terminal boxes (ACS580 drive systems)Allen-Bradley ControlLogix 1756-A chassisAngle grinder gear housingBianchi / Nuova Simonelli / Rheavendors / Saeco vending machineCircular saw blade guard pivotContender Planetary Mixer MXP004/MXP005 (commercial bakery mixer) electrical diagram terminal screwsCordless drill housing shellsCOSEL power supply terminal block (used in industrial/pump/water-treatment control panels)Datalogic DS2400 fixed-mount barcode readerDeWalt D51430 / D51431 pneumatic nailer
Browse all 113 in Industrial & Machinery →The same screw also fits
Devices whose records share a thread with Milwaukee tool torque specification sheet (PN0007936), closest length match first.
- Kadee HO-scale coupler mounting also M2
- KBDfans Tofu60 case also M2
- Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit also M2
- NEMA 17 stepper motor rear shaft cover (Novanta) also M2
- Tofu60 mechanical keyboard case also M2
- Acer Extensa 5210 also M2
- Lenovo LOQ 16APH8 also M2
- HP Compaq nc8430 also M2
Questions about Milwaukee tool torque specification sheet (PN0007936) screws
- What size screw does Milwaukee tool torque specification sheet (PN0007936) use?
- M2 × 0.89 mm for named fastener "Screw M2 x 0.89 PH Torx T6" with a specified seating torque.
- How long are the screws in Milwaukee tool torque specification sheet (PN0007936)?
- The record gives 0.89 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Milwaukee tool torque specification sheet (PN0007936)?
- The source lists a Torx T6 drive. Standard M2 heads otherwise take PH0 (Phillips) or T6 (Torx), or a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.