Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit screw size
M2 · length not stated in the sources
The screws used on Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit are M2. None of the sources we found gives an exact length, so measure the original before you order.
The record covers vendor listing for a feeder screws kit explicitly spanning M2 through M6 sizes used on the feeder mounting hardware.
This entry is marked reported and comes from chinameasure.com.
M2 means a 2 mm nominal diameter with a 0.4 mm thread pitch. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable.
Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | not stated | 0.4 mm | not stated | not stated | Vendor listing for a feeder screws kit explicitly spanning M2 through M6 sizes used on the feeder mounting hardware | Reported |
Fitment records and sources
M2medium
Vendor listing for a feeder screws kit explicitly spanning M2 through M6 sizes used on the feeder mounting hardware
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Industrial parts lists usually give the full callout (thread, length, head, grade); match all four, not just the thread.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- ASUS ROG Ally screw sizes circulating online (M2x16, M2x10) come from a community Q&A, not an ASUS manual — measure before ordering.
- Packaging/labeling equipment manuals (e.g., cab print-and-apply applicators) mix M2 through M6 fasteners across a single machine for very different assemblies (sensors vs. frame vs. drive) — do not generalize one thread size to 'the machine' as a whole; cite the specific subassembly.
More in Industrial & Machinery
ABB ACS580 motor terminal box / cable glandsABB ACS580 terminal hardware (frames R3-R5)ABB random-wound motor terminal boxes (ACS580 drive systems)Allen-Bradley ControlLogix 1756-A chassisAngle grinder gear housingBianchi / Nuova Simonelli / Rheavendors / Saeco vending machineCircular saw blade guard pivotContender Planetary Mixer MXP004/MXP005 (commercial bakery mixer) electrical diagram terminal screwsCordless drill housing shellsCOSEL power supply terminal block (used in industrial/pump/water-treatment control panels)Datalogic DS2400 fixed-mount barcode readerDeWalt D51430 / D51431 pneumatic nailer
Browse all 113 in Industrial & Machinery →The same screw also fits
Devices whose records share a thread with Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit, closest length match first.
- NEMA 17 stepper motor rear shaft cover (Novanta) also M2
- KBDfans Tofu60 case also M2
- Tofu60 mechanical keyboard case also M2
- Milwaukee tool torque specification sheet (PN0007936) also M2
- Kadee HO-scale coupler mounting also M2
- HP Pavilion 16-af0xxx also M2
- Dell Precision 5540 also M2
- Dell Precision M4400 also M2
Questions about Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit screws
- What size screw does Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit use?
- M2 for vendor listing for a feeder screws kit explicitly spanning M2 through M6 sizes used on the feeder mounting hardware.
- How long are the screws in Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Panasonic NPM CM402/CM602 SMT pick-and-place feeder hardware kit?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.