How long are the screws in Pioneer DJ mixer/controller (SX1200 series)?

The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Pioneer DJ mixer/controller (SX1200 series)?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Pioneer DJ mixer/controller (SX1200 series)?

TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.

Pioneer DJ mixer/controller (SX1200 series) screw size

M3 · 6 mm long

If you are replacing a screw on Pioneer DJ mixer/controller (SX1200 series), the thread is M3, 6 mm long.

It is listed for genuine spare part 'SCREW(M3*6)', part number 602-SX1200-544.

This entry is marked confirmed and comes from nps.vegas.

For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Pioneer DJ mixer/controller (SX1200 series) screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	6 mm	0.5 mm	not stated	not stated	Genuine spare part 'SCREW(M3*6)', part number 602-SX1200-544	Confirmed

Fitment records and sources

M36mmhigh

Genuine spare part 'SCREW(M3*6)', part number 602-SX1200-544

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Instrument and audio hardware often threads into wood or thin metal; a screw that is too long can poke through a finished surface.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

Many gas-detector and sensor manuals only give a torque spec (e.g. '0.5 N·m max') without repeating the thread size at every mention — the explicit M3 callout is usually only in the accessories/spare-parts table, not the main installation steps.
M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Audio, Music & Stage

Accordion reed blocks Allparts metric bridge length screws ARRI Mini Follow Focus MFF-2 / related follow-focus hardware Boss compact guitar pedal battery door Cymbal stand / hi-hat wing nut Cymbal stand top wing nut Cymbal stand wing nut Drum hardware wing bolt / memory lock Drum tension rod Drum tension rod / lug mounting screw Duratruss Mini 360 F14 10kg truss clamp Fender Standard Series bass bridge

Browse all 48 in Audio, Music & Stage →

The same screw also fits

Devices whose records share a thread with Pioneer DJ mixer/controller (SX1200 series), closest length match first.

Martin MAC 2000 Performance gobo rotation gear also M3 × 6 mm
Fender/Squier import Stratocaster & Jazzmaster bridge also M3 × 6 mm
Martin MAC 500 moving head fixture also M3 × 6 mm
DIN 912 socket-head cap screw also M3 × 6 mm
Vintage camera / electronics faceplates also M3 × 6 mm
HP LaserJet family common hardware also M3 × 6 mm
Dell P2418D also M3 × 6 mm
Arduino Uno / shield mounting holes also M3 × 6 mm

Questions about Pioneer DJ mixer/controller (SX1200 series) screws

What size screw does Pioneer DJ mixer/controller (SX1200 series) use?: M3 × 6 mm for genuine spare part 'SCREW(M3*6)', part number 602-SX1200-544.
How long are the screws in Pioneer DJ mixer/controller (SX1200 series)?: The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Pioneer DJ mixer/controller (SX1200 series)?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Pioneer DJ mixer/controller (SX1200 series)?: TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.

Heads up: shipping delay